linux/drivers/pci/quirks.c

3112 lines
108 KiB
C
Raw Normal View History

/*
* This file contains work-arounds for many known PCI hardware
* bugs. Devices present only on certain architectures (host
* bridges et cetera) should be handled in arch-specific code.
*
* Note: any quirks for hotpluggable devices must _NOT_ be declared __init.
*
* Copyright (c) 1999 Martin Mares <mj@ucw.cz>
*
* Init/reset quirks for USB host controllers should be in the
* USB quirks file, where their drivers can access reuse it.
*
* The bridge optimization stuff has been removed. If you really
* have a silly BIOS which is unable to set your host bridge right,
* use the PowerTweak utility (see http://powertweak.sourceforge.net).
*/
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/export.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/acpi.h>
#include <linux/kallsyms.h>
#include <linux/dmi.h>
#include <linux/pci-aspm.h>
2009-03-16 08:13:39 +00:00
#include <linux/ioport.h>
#include <linux/sched.h>
#include <linux/ktime.h>
#include <asm/dma.h> /* isa_dma_bridge_buggy */
#include "pci.h"
/*
* Decoding should be disabled for a PCI device during BAR sizing to avoid
* conflict. But doing so may cause problems on host bridge and perhaps other
* key system devices. For devices that need to have mmio decoding always-on,
* we need to set the dev->mmio_always_on bit.
*/
static void __devinit quirk_mmio_always_on(struct pci_dev *dev)
{
dev->mmio_always_on = 1;
}
DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_BRIDGE_HOST, 8, quirk_mmio_always_on);
[PATCH] PCI Bus Parity Status-broken hardware attribute, EDAC foundation Currently, the EDAC (error detection and correction) modules that are in the kernel contain some features that need to be moved. After some good feedback on the PCI Parity detection code and interface (http://www.ussg.iu.edu/hypermail/linux/kernel/0603.1/0897.html) this patch ADDs an new attribute to the pci_dev structure: Namely the 'broken_parity_status' bit. When set this indicates that the respective hardware generates false positives of Parity errors. The EDAC "blacklist" solution was inferior and will be removed in a future patch. Also in this patch is a PCI quirk.c entry for an Infiniband PCI-X card which generates false positive parity errors. I am requesting comments on this AND on the possibility of a exposing this 'broken_parity_status' bit to userland via the PCI device sysfs directory for devices. This access would allow for enabling of this feature on new devices and for old devices that have their drivers updated. (SLES 9 SP3 did this on an ATI motherboard video device). There is a need to update such a PCI attribute between kernel releases. This patch just adds a storage place for the attribute and a quirk entry for a known bad PCI device. PCI Parity reaper/harvestor operations are in EDAC itself and will be refactored to use this PCI attribute instead of its own mechanisms (which are currently disabled) in the future. Signed-off-by: Doug Thompson <norsk5@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-05-09 00:06:09 +00:00
/* The Mellanox Tavor device gives false positive parity errors
* Mark this device with a broken_parity_status, to allow
* PCI scanning code to "skip" this now blacklisted device.
*/
static void __devinit quirk_mellanox_tavor(struct pci_dev *dev)
{
dev->broken_parity_status = 1; /* This device gives false positives */
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX,PCI_DEVICE_ID_MELLANOX_TAVOR,quirk_mellanox_tavor);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX,PCI_DEVICE_ID_MELLANOX_TAVOR_BRIDGE,quirk_mellanox_tavor);
/* Deal with broken BIOS'es that neglect to enable passive release,
which can cause problems in combination with the 82441FX/PPro MTRRs */
static void quirk_passive_release(struct pci_dev *dev)
{
struct pci_dev *d = NULL;
unsigned char dlc;
/* We have to make sure a particular bit is set in the PIIX3
ISA bridge, so we have to go out and find it. */
while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) {
pci_read_config_byte(d, 0x82, &dlc);
if (!(dlc & 1<<1)) {
dev_info(&d->dev, "PIIX3: Enabling Passive Release\n");
dlc |= 1<<1;
pci_write_config_byte(d, 0x82, dlc);
}
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release);
/* The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround
but VIA don't answer queries. If you happen to have good contacts at VIA
ask them for me please -- Alan
This appears to be BIOS not version dependent. So presumably there is a
chipset level fix */
static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev)
{
if (!isa_dma_bridge_buggy) {
isa_dma_bridge_buggy=1;
dev_info(&dev->dev, "Activating ISA DMA hang workarounds\n");
}
}
/*
* Its not totally clear which chipsets are the problematic ones
* We know 82C586 and 82C596 variants are affected.
*/
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs);
/*
* Intel NM10 "TigerPoint" LPC PM1a_STS.BM_STS must be clear
* for some HT machines to use C4 w/o hanging.
*/
static void __devinit quirk_tigerpoint_bm_sts(struct pci_dev *dev)
{
u32 pmbase;
u16 pm1a;
pci_read_config_dword(dev, 0x40, &pmbase);
pmbase = pmbase & 0xff80;
pm1a = inw(pmbase);
if (pm1a & 0x10) {
dev_info(&dev->dev, FW_BUG "TigerPoint LPC.BM_STS cleared\n");
outw(0x10, pmbase);
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TGP_LPC, quirk_tigerpoint_bm_sts);
/*
* Chipsets where PCI->PCI transfers vanish or hang
*/
static void __devinit quirk_nopcipci(struct pci_dev *dev)
{
if ((pci_pci_problems & PCIPCI_FAIL)==0) {
dev_info(&dev->dev, "Disabling direct PCI/PCI transfers\n");
pci_pci_problems |= PCIPCI_FAIL;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci);
static void __devinit quirk_nopciamd(struct pci_dev *dev)
{
u8 rev;
pci_read_config_byte(dev, 0x08, &rev);
if (rev == 0x13) {
/* Erratum 24 */
dev_info(&dev->dev, "Chipset erratum: Disabling direct PCI/AGP transfers\n");
pci_pci_problems |= PCIAGP_FAIL;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8151_0, quirk_nopciamd);
/*
* Triton requires workarounds to be used by the drivers
*/
static void __devinit quirk_triton(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_TRITON)==0) {
dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
pci_pci_problems |= PCIPCI_TRITON;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton);
/*
* VIA Apollo KT133 needs PCI latency patch
* Made according to a windows driver based patch by George E. Breese
* see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm
* and http://www.georgebreese.com/net/software/#PCI
* Also see http://www.au-ja.org/review-kt133a-1-en.phtml for
* the info on which Mr Breese based his work.
*
* Updated based on further information from the site and also on
* information provided by VIA
*/
static void quirk_vialatency(struct pci_dev *dev)
{
struct pci_dev *p;
u8 busarb;
/* Ok we have a potential problem chipset here. Now see if we have
a buggy southbridge */
p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL);
if (p!=NULL) {
/* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */
/* Check for buggy part revisions */
if (p->revision < 0x40 || p->revision > 0x42)
goto exit;
} else {
p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL);
if (p==NULL) /* No problem parts */
goto exit;
/* Check for buggy part revisions */
if (p->revision < 0x10 || p->revision > 0x12)
goto exit;
}
/*
* Ok we have the problem. Now set the PCI master grant to
* occur every master grant. The apparent bug is that under high
* PCI load (quite common in Linux of course) you can get data
* loss when the CPU is held off the bus for 3 bus master requests
* This happens to include the IDE controllers....
*
* VIA only apply this fix when an SB Live! is present but under
* both Linux and Windows this isn't enough, and we have seen
* corruption without SB Live! but with things like 3 UDMA IDE
* controllers. So we ignore that bit of the VIA recommendation..
*/
pci_read_config_byte(dev, 0x76, &busarb);
/* Set bit 4 and bi 5 of byte 76 to 0x01
"Master priority rotation on every PCI master grant */
busarb &= ~(1<<5);
busarb |= (1<<4);
pci_write_config_byte(dev, 0x76, busarb);
dev_info(&dev->dev, "Applying VIA southbridge workaround\n");
exit:
pci_dev_put(p);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency);
/* Must restore this on a resume from RAM */
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency);
/*
* VIA Apollo VP3 needs ETBF on BT848/878
*/
static void __devinit quirk_viaetbf(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_VIAETBF)==0) {
dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
pci_pci_problems |= PCIPCI_VIAETBF;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf);
static void __devinit quirk_vsfx(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_VSFX)==0) {
dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
pci_pci_problems |= PCIPCI_VSFX;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx);
/*
* Ali Magik requires workarounds to be used by the drivers
* that DMA to AGP space. Latency must be set to 0xA and triton
* workaround applied too
* [Info kindly provided by ALi]
*/
static void __init quirk_alimagik(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) {
dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik);
/*
* Natoma has some interesting boundary conditions with Zoran stuff
* at least
*/
static void __devinit quirk_natoma(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_NATOMA)==0) {
dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
pci_pci_problems |= PCIPCI_NATOMA;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma);
/*
* This chip can cause PCI parity errors if config register 0xA0 is read
* while DMAs are occurring.
*/
static void __devinit quirk_citrine(struct pci_dev *dev)
{
dev->cfg_size = 0xA0;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine);
/*
* S3 868 and 968 chips report region size equal to 32M, but they decode 64M.
* If it's needed, re-allocate the region.
*/
static void __devinit quirk_s3_64M(struct pci_dev *dev)
{
struct resource *r = &dev->resource[0];
if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) {
r->start = 0;
r->end = 0x3ffffff;
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M);
/*
* Some CS5536 BIOSes (for example, the Soekris NET5501 board w/ comBIOS
* ver. 1.33 20070103) don't set the correct ISA PCI region header info.
* BAR0 should be 8 bytes; instead, it may be set to something like 8k
* (which conflicts w/ BAR1's memory range).
*/
static void __devinit quirk_cs5536_vsa(struct pci_dev *dev)
{
if (pci_resource_len(dev, 0) != 8) {
struct resource *res = &dev->resource[0];
res->end = res->start + 8 - 1;
dev_info(&dev->dev, "CS5536 ISA bridge bug detected "
"(incorrect header); workaround applied.\n");
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa);
static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region,
unsigned size, int nr, const char *name)
{
region &= ~(size-1);
if (region) {
[PATCH] Make sparc64 use setup-res.c There were three changes necessary in order to allow sparc64 to use setup-res.c: 1) Sparc64 roots the PCI I/O and MEM address space using parent resources contained in the PCI controller structure. I'm actually surprised no other platforms do this, especially ones like Alpha and PPC{,64}. These resources get linked into the iomem/ioport tree when PCI controllers are probed. So the hierarchy looks like this: iomem --| PCI controller 1 MEM space --| device 1 device 2 etc. PCI controller 2 MEM space --| ... ioport --| PCI controller 1 IO space --| ... PCI controller 2 IO space --| ... You get the idea. The drivers/pci/setup-res.c code allocates using plain iomem_space and ioport_space as the root, so that wouldn't work with the above setup. So I added a pcibios_select_root() that is used to handle this. It uses the PCI controller struct's io_space and mem_space on sparc64, and io{port,mem}_resource on every other platform to keep current behavior. 2) quirk_io_region() is buggy. It takes in raw BUS view addresses and tries to use them as a PCI resource. pci_claim_resource() expects the resource to be fully formed when it gets called. The sparc64 implementation would do the translation but that's absolutely wrong, because if the same resource gets released then re-claimed we'll adjust things twice. So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource() conversion before passing it on to pci_claim_resource(). 3) I was mistakedly __init'ing the function methods the PCI controller drivers provide on sparc64 to implement some parts of these routines. This was, of course, easy to fix. So we end up with the following, and that nasty SPARC64 makefile ifdef in drivers/pci/Makefile is finally zapped. Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-08-08 20:19:08 +00:00
struct pci_bus_region bus_region;
struct resource *res = dev->resource + nr;
res->name = pci_name(dev);
res->start = region;
res->end = region + size - 1;
res->flags = IORESOURCE_IO;
[PATCH] Make sparc64 use setup-res.c There were three changes necessary in order to allow sparc64 to use setup-res.c: 1) Sparc64 roots the PCI I/O and MEM address space using parent resources contained in the PCI controller structure. I'm actually surprised no other platforms do this, especially ones like Alpha and PPC{,64}. These resources get linked into the iomem/ioport tree when PCI controllers are probed. So the hierarchy looks like this: iomem --| PCI controller 1 MEM space --| device 1 device 2 etc. PCI controller 2 MEM space --| ... ioport --| PCI controller 1 IO space --| ... PCI controller 2 IO space --| ... You get the idea. The drivers/pci/setup-res.c code allocates using plain iomem_space and ioport_space as the root, so that wouldn't work with the above setup. So I added a pcibios_select_root() that is used to handle this. It uses the PCI controller struct's io_space and mem_space on sparc64, and io{port,mem}_resource on every other platform to keep current behavior. 2) quirk_io_region() is buggy. It takes in raw BUS view addresses and tries to use them as a PCI resource. pci_claim_resource() expects the resource to be fully formed when it gets called. The sparc64 implementation would do the translation but that's absolutely wrong, because if the same resource gets released then re-claimed we'll adjust things twice. So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource() conversion before passing it on to pci_claim_resource(). 3) I was mistakedly __init'ing the function methods the PCI controller drivers provide on sparc64 to implement some parts of these routines. This was, of course, easy to fix. So we end up with the following, and that nasty SPARC64 makefile ifdef in drivers/pci/Makefile is finally zapped. Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-08-08 20:19:08 +00:00
/* Convert from PCI bus to resource space. */
bus_region.start = res->start;
bus_region.end = res->end;
pcibios_bus_to_resource(dev, res, &bus_region);
if (pci_claim_resource(dev, nr) == 0)
dev_info(&dev->dev, "quirk: %pR claimed by %s\n",
res, name);
}
}
/*
* ATI Northbridge setups MCE the processor if you even
* read somewhere between 0x3b0->0x3bb or read 0x3d3
*/
static void __devinit quirk_ati_exploding_mce(struct pci_dev *dev)
{
dev_info(&dev->dev, "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb\n");
/* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */
request_region(0x3b0, 0x0C, "RadeonIGP");
request_region(0x3d3, 0x01, "RadeonIGP");
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce);
/*
* Let's make the southbridge information explicit instead
* of having to worry about people probing the ACPI areas,
* for example.. (Yes, it happens, and if you read the wrong
* ACPI register it will put the machine to sleep with no
* way of waking it up again. Bummer).
*
* ALI M7101: Two IO regions pointed to by words at
* 0xE0 (64 bytes of ACPI registers)
* 0xE2 (32 bytes of SMB registers)
*/
static void __devinit quirk_ali7101_acpi(struct pci_dev *dev)
{
u16 region;
pci_read_config_word(dev, 0xE0, &region);
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "ali7101 ACPI");
pci_read_config_word(dev, 0xE2, &region);
quirk_io_region(dev, region, 32, PCI_BRIDGE_RESOURCES+1, "ali7101 SMB");
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi);
static void piix4_io_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable)
{
u32 devres;
u32 mask, size, base;
pci_read_config_dword(dev, port, &devres);
if ((devres & enable) != enable)
return;
mask = (devres >> 16) & 15;
base = devres & 0xffff;
size = 16;
for (;;) {
unsigned bit = size >> 1;
if ((bit & mask) == bit)
break;
size = bit;
}
/*
* For now we only print it out. Eventually we'll want to
* reserve it (at least if it's in the 0x1000+ range), but
* let's get enough confirmation reports first.
*/
base &= -size;
dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base + size - 1);
}
static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable)
{
u32 devres;
u32 mask, size, base;
pci_read_config_dword(dev, port, &devres);
if ((devres & enable) != enable)
return;
base = devres & 0xffff0000;
mask = (devres & 0x3f) << 16;
size = 128 << 16;
for (;;) {
unsigned bit = size >> 1;
if ((bit & mask) == bit)
break;
size = bit;
}
/*
* For now we only print it out. Eventually we'll want to
* reserve it, but let's get enough confirmation reports first.
*/
base &= -size;
dev_info(&dev->dev, "%s MMIO at %04x-%04x\n", name, base, base + size - 1);
}
/*
* PIIX4 ACPI: Two IO regions pointed to by longwords at
* 0x40 (64 bytes of ACPI registers)
* 0x90 (16 bytes of SMB registers)
* and a few strange programmable PIIX4 device resources.
*/
static void __devinit quirk_piix4_acpi(struct pci_dev *dev)
{
u32 region, res_a;
pci_read_config_dword(dev, 0x40, &region);
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI");
pci_read_config_dword(dev, 0x90, &region);
quirk_io_region(dev, region, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB");
/* Device resource A has enables for some of the other ones */
pci_read_config_dword(dev, 0x5c, &res_a);
piix4_io_quirk(dev, "PIIX4 devres B", 0x60, 3 << 21);
piix4_io_quirk(dev, "PIIX4 devres C", 0x64, 3 << 21);
/* Device resource D is just bitfields for static resources */
/* Device 12 enabled? */
if (res_a & (1 << 29)) {
piix4_io_quirk(dev, "PIIX4 devres E", 0x68, 1 << 20);
piix4_mem_quirk(dev, "PIIX4 devres F", 0x6c, 1 << 7);
}
/* Device 13 enabled? */
if (res_a & (1 << 30)) {
piix4_io_quirk(dev, "PIIX4 devres G", 0x70, 1 << 20);
piix4_mem_quirk(dev, "PIIX4 devres H", 0x74, 1 << 7);
}
piix4_io_quirk(dev, "PIIX4 devres I", 0x78, 1 << 20);
piix4_io_quirk(dev, "PIIX4 devres J", 0x7c, 1 << 20);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_3, quirk_piix4_acpi);
#define ICH_PMBASE 0x40
#define ICH_ACPI_CNTL 0x44
#define ICH4_ACPI_EN 0x10
#define ICH6_ACPI_EN 0x80
#define ICH4_GPIOBASE 0x58
#define ICH4_GPIO_CNTL 0x5c
#define ICH4_GPIO_EN 0x10
#define ICH6_GPIOBASE 0x48
#define ICH6_GPIO_CNTL 0x4c
#define ICH6_GPIO_EN 0x10
/*
* ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at
* 0x40 (128 bytes of ACPI, GPIO & TCO registers)
* 0x58 (64 bytes of GPIO I/O space)
*/
static void __devinit quirk_ich4_lpc_acpi(struct pci_dev *dev)
{
u32 region;
u8 enable;
/*
* The check for PCIBIOS_MIN_IO is to ensure we won't create a conflict
* with low legacy (and fixed) ports. We don't know the decoding
* priority and can't tell whether the legacy device or the one created
* here is really at that address. This happens on boards with broken
* BIOSes.
*/
pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable);
if (enable & ICH4_ACPI_EN) {
pci_read_config_dword(dev, ICH_PMBASE, &region);
region &= PCI_BASE_ADDRESS_IO_MASK;
if (region >= PCIBIOS_MIN_IO)
quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES,
"ICH4 ACPI/GPIO/TCO");
}
pci_read_config_byte(dev, ICH4_GPIO_CNTL, &enable);
if (enable & ICH4_GPIO_EN) {
pci_read_config_dword(dev, ICH4_GPIOBASE, &region);
region &= PCI_BASE_ADDRESS_IO_MASK;
if (region >= PCIBIOS_MIN_IO)
quirk_io_region(dev, region, 64,
PCI_BRIDGE_RESOURCES + 1, "ICH4 GPIO");
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi);
static void __devinit ich6_lpc_acpi_gpio(struct pci_dev *dev)
{
u32 region;
u8 enable;
pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable);
if (enable & ICH6_ACPI_EN) {
pci_read_config_dword(dev, ICH_PMBASE, &region);
region &= PCI_BASE_ADDRESS_IO_MASK;
if (region >= PCIBIOS_MIN_IO)
quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES,
"ICH6 ACPI/GPIO/TCO");
}
pci_read_config_byte(dev, ICH6_GPIO_CNTL, &enable);
if (enable & ICH6_GPIO_EN) {
pci_read_config_dword(dev, ICH6_GPIOBASE, &region);
region &= PCI_BASE_ADDRESS_IO_MASK;
if (region >= PCIBIOS_MIN_IO)
quirk_io_region(dev, region, 64,
PCI_BRIDGE_RESOURCES + 1, "ICH6 GPIO");
}
}
static void __devinit ich6_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name, int dynsize)
{
u32 val;
u32 size, base;
pci_read_config_dword(dev, reg, &val);
/* Enabled? */
if (!(val & 1))
return;
base = val & 0xfffc;
if (dynsize) {
/*
* This is not correct. It is 16, 32 or 64 bytes depending on
* register D31:F0:ADh bits 5:4.
*
* But this gets us at least _part_ of it.
*/
size = 16;
} else {
size = 128;
}
base &= ~(size-1);
/* Just print it out for now. We should reserve it after more debugging */
dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base+size-1);
}
static void __devinit quirk_ich6_lpc(struct pci_dev *dev)
{
/* Shared ACPI/GPIO decode with all ICH6+ */
ich6_lpc_acpi_gpio(dev);
/* ICH6-specific generic IO decode */
ich6_lpc_generic_decode(dev, 0x84, "LPC Generic IO decode 1", 0);
ich6_lpc_generic_decode(dev, 0x88, "LPC Generic IO decode 2", 1);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc);
static void __devinit ich7_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name)
{
u32 val;
u32 mask, base;
pci_read_config_dword(dev, reg, &val);
/* Enabled? */
if (!(val & 1))
return;
/*
* IO base in bits 15:2, mask in bits 23:18, both
* are dword-based
*/
base = val & 0xfffc;
mask = (val >> 16) & 0xfc;
mask |= 3;
/* Just print it out for now. We should reserve it after more debugging */
dev_info(&dev->dev, "%s PIO at %04x (mask %04x)\n", name, base, mask);
}
/* ICH7-10 has the same common LPC generic IO decode registers */
static void __devinit quirk_ich7_lpc(struct pci_dev *dev)
{
/* We share the common ACPI/GPIO decode with ICH6 */
ich6_lpc_acpi_gpio(dev);
/* And have 4 ICH7+ generic decodes */
ich7_lpc_generic_decode(dev, 0x84, "ICH7 LPC Generic IO decode 1");
ich7_lpc_generic_decode(dev, 0x88, "ICH7 LPC Generic IO decode 2");
ich7_lpc_generic_decode(dev, 0x8c, "ICH7 LPC Generic IO decode 3");
ich7_lpc_generic_decode(dev, 0x90, "ICH7 LPC Generic IO decode 4");
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich7_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_1, quirk_ich7_lpc);
/*
* VIA ACPI: One IO region pointed to by longword at
* 0x48 or 0x20 (256 bytes of ACPI registers)
*/
static void __devinit quirk_vt82c586_acpi(struct pci_dev *dev)
{
u32 region;
if (dev->revision & 0x10) {
pci_read_config_dword(dev, 0x48, &region);
region &= PCI_BASE_ADDRESS_IO_MASK;
quirk_io_region(dev, region, 256, PCI_BRIDGE_RESOURCES, "vt82c586 ACPI");
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi);
/*
* VIA VT82C686 ACPI: Three IO region pointed to by (long)words at
* 0x48 (256 bytes of ACPI registers)
* 0x70 (128 bytes of hardware monitoring register)
* 0x90 (16 bytes of SMB registers)
*/
static void __devinit quirk_vt82c686_acpi(struct pci_dev *dev)
{
u16 hm;
u32 smb;
quirk_vt82c586_acpi(dev);
pci_read_config_word(dev, 0x70, &hm);
hm &= PCI_BASE_ADDRESS_IO_MASK;
quirk_io_region(dev, hm, 128, PCI_BRIDGE_RESOURCES + 1, "vt82c686 HW-mon");
pci_read_config_dword(dev, 0x90, &smb);
smb &= PCI_BASE_ADDRESS_IO_MASK;
quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 2, "vt82c686 SMB");
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi);
/*
* VIA VT8235 ISA Bridge: Two IO regions pointed to by words at
* 0x88 (128 bytes of power management registers)
* 0xd0 (16 bytes of SMB registers)
*/
static void __devinit quirk_vt8235_acpi(struct pci_dev *dev)
{
u16 pm, smb;
pci_read_config_word(dev, 0x88, &pm);
pm &= PCI_BASE_ADDRESS_IO_MASK;
quirk_io_region(dev, pm, 128, PCI_BRIDGE_RESOURCES, "vt8235 PM");
pci_read_config_word(dev, 0xd0, &smb);
smb &= PCI_BASE_ADDRESS_IO_MASK;
quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 1, "vt8235 SMB");
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi);
/*
* TI XIO2000a PCIe-PCI Bridge erroneously reports it supports fast back-to-back:
* Disable fast back-to-back on the secondary bus segment
*/
static void __devinit quirk_xio2000a(struct pci_dev *dev)
{
struct pci_dev *pdev;
u16 command;
dev_warn(&dev->dev, "TI XIO2000a quirk detected; "
"secondary bus fast back-to-back transfers disabled\n");
list_for_each_entry(pdev, &dev->subordinate->devices, bus_list) {
pci_read_config_word(pdev, PCI_COMMAND, &command);
if (command & PCI_COMMAND_FAST_BACK)
pci_write_config_word(pdev, PCI_COMMAND, command & ~PCI_COMMAND_FAST_BACK);
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2000A,
quirk_xio2000a);
#ifdef CONFIG_X86_IO_APIC
#include <asm/io_apic.h>
/*
* VIA 686A/B: If an IO-APIC is active, we need to route all on-chip
* devices to the external APIC.
*
* TODO: When we have device-specific interrupt routers,
* this code will go away from quirks.
*/
static void quirk_via_ioapic(struct pci_dev *dev)
{
u8 tmp;
if (nr_ioapics < 1)
tmp = 0; /* nothing routed to external APIC */
else
tmp = 0x1f; /* all known bits (4-0) routed to external APIC */
dev_info(&dev->dev, "%sbling VIA external APIC routing\n",
tmp == 0 ? "Disa" : "Ena");
/* Offset 0x58: External APIC IRQ output control */
pci_write_config_byte (dev, 0x58, tmp);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic);
/*
* VIA 8237: Some BIOSs don't set the 'Bypass APIC De-Assert Message' Bit.
* This leads to doubled level interrupt rates.
* Set this bit to get rid of cycle wastage.
* Otherwise uncritical.
*/
static void quirk_via_vt8237_bypass_apic_deassert(struct pci_dev *dev)
{
u8 misc_control2;
#define BYPASS_APIC_DEASSERT 8
pci_read_config_byte(dev, 0x5B, &misc_control2);
if (!(misc_control2 & BYPASS_APIC_DEASSERT)) {
dev_info(&dev->dev, "Bypassing VIA 8237 APIC De-Assert Message\n");
pci_write_config_byte(dev, 0x5B, misc_control2|BYPASS_APIC_DEASSERT);
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert);
/*
* The AMD io apic can hang the box when an apic irq is masked.
* We check all revs >= B0 (yet not in the pre production!) as the bug
* is currently marked NoFix
*
* We have multiple reports of hangs with this chipset that went away with
* noapic specified. For the moment we assume it's the erratum. We may be wrong
* of course. However the advice is demonstrably good even if so..
*/
static void __devinit quirk_amd_ioapic(struct pci_dev *dev)
{
if (dev->revision >= 0x02) {
dev_warn(&dev->dev, "I/O APIC: AMD Erratum #22 may be present. In the event of instability try\n");
dev_warn(&dev->dev, " : booting with the \"noapic\" option\n");
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic);
static void __init quirk_ioapic_rmw(struct pci_dev *dev)
{
if (dev->devfn == 0 && dev->bus->number == 0)
sis_apic_bug = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_ANY_ID, quirk_ioapic_rmw);
#endif /* CONFIG_X86_IO_APIC */
/*
* Some settings of MMRBC can lead to data corruption so block changes.
* See AMD 8131 HyperTransport PCI-X Tunnel Revision Guide
*/
static void __init quirk_amd_8131_mmrbc(struct pci_dev *dev)
{
if (dev->subordinate && dev->revision <= 0x12) {
dev_info(&dev->dev, "AMD8131 rev %x detected; "
"disabling PCI-X MMRBC\n", dev->revision);
dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MMRBC;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_mmrbc);
/*
* FIXME: it is questionable that quirk_via_acpi
* is needed. It shows up as an ISA bridge, and does not
* support the PCI_INTERRUPT_LINE register at all. Therefore
* it seems like setting the pci_dev's 'irq' to the
* value of the ACPI SCI interrupt is only done for convenience.
* -jgarzik
*/
static void __devinit quirk_via_acpi(struct pci_dev *d)
{
/*
* VIA ACPI device: SCI IRQ line in PCI config byte 0x42
*/
u8 irq;
pci_read_config_byte(d, 0x42, &irq);
irq &= 0xf;
if (irq && (irq != 2))
d->irq = irq;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi);
/*
* VIA bridges which have VLink
*/
static int via_vlink_dev_lo = -1, via_vlink_dev_hi = 18;
static void quirk_via_bridge(struct pci_dev *dev)
{
/* See what bridge we have and find the device ranges */
switch (dev->device) {
case PCI_DEVICE_ID_VIA_82C686:
/* The VT82C686 is special, it attaches to PCI and can have
any device number. All its subdevices are functions of
that single device. */
via_vlink_dev_lo = PCI_SLOT(dev->devfn);
via_vlink_dev_hi = PCI_SLOT(dev->devfn);
break;
case PCI_DEVICE_ID_VIA_8237:
case PCI_DEVICE_ID_VIA_8237A:
via_vlink_dev_lo = 15;
break;
case PCI_DEVICE_ID_VIA_8235:
via_vlink_dev_lo = 16;
break;
case PCI_DEVICE_ID_VIA_8231:
case PCI_DEVICE_ID_VIA_8233_0:
case PCI_DEVICE_ID_VIA_8233A:
case PCI_DEVICE_ID_VIA_8233C_0:
via_vlink_dev_lo = 17;
break;
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_bridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, quirk_via_bridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_0, quirk_via_bridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233A, quirk_via_bridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233C_0, quirk_via_bridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_via_bridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_bridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237A, quirk_via_bridge);
/**
* quirk_via_vlink - VIA VLink IRQ number update
* @dev: PCI device
*
* If the device we are dealing with is on a PIC IRQ we need to
* ensure that the IRQ line register which usually is not relevant
* for PCI cards, is actually written so that interrupts get sent
* to the right place.
* We only do this on systems where a VIA south bridge was detected,
* and only for VIA devices on the motherboard (see quirk_via_bridge
* above).
*/
static void quirk_via_vlink(struct pci_dev *dev)
{
u8 irq, new_irq;
/* Check if we have VLink at all */
if (via_vlink_dev_lo == -1)
return;
new_irq = dev->irq;
/* Don't quirk interrupts outside the legacy IRQ range */
if (!new_irq || new_irq > 15)
return;
/* Internal device ? */
if (dev->bus->number != 0 || PCI_SLOT(dev->devfn) > via_vlink_dev_hi ||
PCI_SLOT(dev->devfn) < via_vlink_dev_lo)
return;
/* This is an internal VLink device on a PIC interrupt. The BIOS
ought to have set this but may not have, so we redo it */
pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
if (new_irq != irq) {
dev_info(&dev->dev, "VIA VLink IRQ fixup, from %d to %d\n",
irq, new_irq);
udelay(15); /* unknown if delay really needed */
pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq);
}
}
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_vlink);
/*
* VIA VT82C598 has its device ID settable and many BIOSes
* set it to the ID of VT82C597 for backward compatibility.
* We need to switch it off to be able to recognize the real
* type of the chip.
*/
static void __devinit quirk_vt82c598_id(struct pci_dev *dev)
{
pci_write_config_byte(dev, 0xfc, 0);
pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id);
/*
* CardBus controllers have a legacy base address that enables them
* to respond as i82365 pcmcia controllers. We don't want them to
* do this even if the Linux CardBus driver is not loaded, because
* the Linux i82365 driver does not (and should not) handle CardBus.
*/
static void quirk_cardbus_legacy(struct pci_dev *dev)
{
pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0);
}
DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_BRIDGE_CARDBUS, 8, quirk_cardbus_legacy);
DECLARE_PCI_FIXUP_CLASS_RESUME_EARLY(PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_BRIDGE_CARDBUS, 8, quirk_cardbus_legacy);
/*
* Following the PCI ordering rules is optional on the AMD762. I'm not
* sure what the designers were smoking but let's not inhale...
*
* To be fair to AMD, it follows the spec by default, its BIOS people
* who turn it off!
*/
static void quirk_amd_ordering(struct pci_dev *dev)
{
u32 pcic;
pci_read_config_dword(dev, 0x4C, &pcic);
if ((pcic&6)!=6) {
pcic |= 6;
dev_warn(&dev->dev, "BIOS failed to enable PCI standards compliance; fixing this error\n");
pci_write_config_dword(dev, 0x4C, pcic);
pci_read_config_dword(dev, 0x84, &pcic);
pcic |= (1<<23); /* Required in this mode */
pci_write_config_dword(dev, 0x84, pcic);
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering);
/*
* DreamWorks provided workaround for Dunord I-3000 problem
*
* This card decodes and responds to addresses not apparently
* assigned to it. We force a larger allocation to ensure that
* nothing gets put too close to it.
*/
static void __devinit quirk_dunord ( struct pci_dev * dev )
{
struct resource *r = &dev->resource [1];
r->start = 0;
r->end = 0xffffff;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord);
/*
* i82380FB mobile docking controller: its PCI-to-PCI bridge
* is subtractive decoding (transparent), and does indicate this
* in the ProgIf. Unfortunately, the ProgIf value is wrong - 0x80
* instead of 0x01.
*/
static void __devinit quirk_transparent_bridge(struct pci_dev *dev)
{
dev->transparent = 1;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge);
/*
* Common misconfiguration of the MediaGX/Geode PCI master that will
* reduce PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1
* datasheets found at http://www.national.com/analog for info on what
* these bits do. <christer@weinigel.se>
*/
static void quirk_mediagx_master(struct pci_dev *dev)
{
u8 reg;
pci_read_config_byte(dev, 0x41, &reg);
if (reg & 2) {
reg &= ~2;
dev_info(&dev->dev, "Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", reg);
pci_write_config_byte(dev, 0x41, reg);
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master);
/*
* Ensure C0 rev restreaming is off. This is normally done by
* the BIOS but in the odd case it is not the results are corruption
* hence the presence of a Linux check
*/
static void quirk_disable_pxb(struct pci_dev *pdev)
{
u16 config;
if (pdev->revision != 0x04) /* Only C0 requires this */
return;
pci_read_config_word(pdev, 0x40, &config);
if (config & (1<<6)) {
config &= ~(1<<6);
pci_write_config_word(pdev, 0x40, config);
dev_info(&pdev->dev, "C0 revision 450NX. Disabling PCI restreaming\n");
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb);
static void __devinit quirk_amd_ide_mode(struct pci_dev *pdev)
{
/* set SBX00/Hudson-2 SATA in IDE mode to AHCI mode */
u8 tmp;
pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &tmp);
if (tmp == 0x01) {
pci_read_config_byte(pdev, 0x40, &tmp);
pci_write_config_byte(pdev, 0x40, tmp|1);
pci_write_config_byte(pdev, 0x9, 1);
pci_write_config_byte(pdev, 0xa, 6);
pci_write_config_byte(pdev, 0x40, tmp);
pdev->class = PCI_CLASS_STORAGE_SATA_AHCI;
dev_info(&pdev->dev, "set SATA to AHCI mode\n");
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode);
/*
* Serverworks CSB5 IDE does not fully support native mode
*/
static void __devinit quirk_svwks_csb5ide(struct pci_dev *pdev)
{
u8 prog;
pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
if (prog & 5) {
prog &= ~5;
pdev->class &= ~5;
pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
/* PCI layer will sort out resources */
}
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide);
/*
* Intel 82801CAM ICH3-M datasheet says IDE modes must be the same
*/
static void __init quirk_ide_samemode(struct pci_dev *pdev)
{
u8 prog;
pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) {
dev_info(&pdev->dev, "IDE mode mismatch; forcing legacy mode\n");
prog &= ~5;
pdev->class &= ~5;
pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
}
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode);
/*
* Some ATA devices break if put into D3
*/
static void __devinit quirk_no_ata_d3(struct pci_dev *pdev)
{
pdev->dev_flags |= PCI_DEV_FLAGS_NO_D3;
}
/* Quirk the legacy ATA devices only. The AHCI ones are ok */
DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_ANY_ID,
PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3);
DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_ATI, PCI_ANY_ID,
PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3);
/* ALi loses some register settings that we cannot then restore */
DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID,
PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3);
/* VIA comes back fine but we need to keep it alive or ACPI GTM failures
occur when mode detecting */
DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_VIA, PCI_ANY_ID,
PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3);
/* This was originally an Alpha specific thing, but it really fits here.
* The i82375 PCI/EISA bridge appears as non-classified. Fix that.
*/
static void __init quirk_eisa_bridge(struct pci_dev *dev)
{
dev->class = PCI_CLASS_BRIDGE_EISA << 8;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge);
/*
* On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge
* is not activated. The myth is that Asus said that they do not want the
* users to be irritated by just another PCI Device in the Win98 device
* manager. (see the file prog/hotplug/README.p4b in the lm_sensors
* package 2.7.0 for details)
*
* The SMBus PCI Device can be activated by setting a bit in the ICH LPC
* bridge. Unfortunately, this device has no subvendor/subdevice ID. So it
* becomes necessary to do this tweak in two steps -- the chosen trigger
* is either the Host bridge (preferred) or on-board VGA controller.
*
* Note that we used to unhide the SMBus that way on Toshiba laptops
* (Satellite A40 and Tecra M2) but then found that the thermal management
* was done by SMM code, which could cause unsynchronized concurrent
* accesses to the SMBus registers, with potentially bad effects. Thus you
* should be very careful when adding new entries: if SMM is accessing the
* Intel SMBus, this is a very good reason to leave it hidden.
*
* Likewise, many recent laptops use ACPI for thermal management. If the
* ACPI DSDT code accesses the SMBus, then Linux should not access it
* natively, and keeping the SMBus hidden is the right thing to do. If you
* are about to add an entry in the table below, please first disassemble
* the DSDT and double-check that there is no code accessing the SMBus.
*/
static int asus_hides_smbus;
static void __init asus_hides_smbus_hostbridge(struct pci_dev *dev)
{
if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB)
switch(dev->subsystem_device) {
case 0x8025: /* P4B-LX */
case 0x8070: /* P4B */
case 0x8088: /* P4B533 */
case 0x1626: /* L3C notebook */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB)
switch(dev->subsystem_device) {
case 0x80b1: /* P4GE-V */
case 0x80b2: /* P4PE */
case 0x8093: /* P4B533-V */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB)
switch(dev->subsystem_device) {
case 0x8030: /* P4T533 */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_7205_0)
switch (dev->subsystem_device) {
case 0x8070: /* P4G8X Deluxe */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_E7501_MCH)
switch (dev->subsystem_device) {
case 0x80c9: /* PU-DLS */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB)
switch (dev->subsystem_device) {
case 0x1751: /* M2N notebook */
case 0x1821: /* M5N notebook */
case 0x1897: /* A6L notebook */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch (dev->subsystem_device) {
case 0x184b: /* W1N notebook */
case 0x186a: /* M6Ne notebook */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB)
switch (dev->subsystem_device) {
case 0x80f2: /* P4P800-X */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB)
switch (dev->subsystem_device) {
case 0x1882: /* M6V notebook */
case 0x1977: /* A6VA notebook */
asus_hides_smbus = 1;
}
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch(dev->subsystem_device) {
case 0x088C: /* HP Compaq nc8000 */
case 0x0890: /* HP Compaq nc6000 */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB)
switch (dev->subsystem_device) {
case 0x12bc: /* HP D330L */
case 0x12bd: /* HP D530 */
case 0x006a: /* HP Compaq nx9500 */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82875_HB)
switch (dev->subsystem_device) {
case 0x12bf: /* HP xw4100 */
asus_hides_smbus = 1;
}
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch(dev->subsystem_device) {
case 0xC00C: /* Samsung P35 notebook */
asus_hides_smbus = 1;
}
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch(dev->subsystem_device) {
case 0x0058: /* Compaq Evo N620c */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82810_IG3)
switch(dev->subsystem_device) {
case 0xB16C: /* Compaq Deskpro EP 401963-001 (PCA# 010174) */
/* Motherboard doesn't have Host bridge
* subvendor/subdevice IDs, therefore checking
* its on-board VGA controller */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82801DB_2)
switch(dev->subsystem_device) {
case 0x00b8: /* Compaq Evo D510 CMT */
case 0x00b9: /* Compaq Evo D510 SFF */
case 0x00ba: /* Compaq Evo D510 USDT */
/* Motherboard doesn't have Host bridge
* subvendor/subdevice IDs and on-board VGA
* controller is disabled if an AGP card is
* inserted, therefore checking USB UHCI
* Controller #1 */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82815_CGC)
switch (dev->subsystem_device) {
case 0x001A: /* Compaq Deskpro EN SSF P667 815E */
/* Motherboard doesn't have host bridge
* subvendor/subdevice IDs, therefore checking
* its on-board VGA controller */
asus_hides_smbus = 1;
}
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7501_MCH, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_2, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC, asus_hides_smbus_hostbridge);
static void asus_hides_smbus_lpc(struct pci_dev *dev)
{
u16 val;
if (likely(!asus_hides_smbus))
return;
pci_read_config_word(dev, 0xF2, &val);
if (val & 0x8) {
pci_write_config_word(dev, 0xF2, val & (~0x8));
pci_read_config_word(dev, 0xF2, &val);
if (val & 0x8)
dev_info(&dev->dev, "i801 SMBus device continues to play 'hide and seek'! 0x%x\n", val);
else
dev_info(&dev->dev, "Enabled i801 SMBus device\n");
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc);
/* It appears we just have one such device. If not, we have a warning */
static void __iomem *asus_rcba_base;
static void asus_hides_smbus_lpc_ich6_suspend(struct pci_dev *dev)
{
u32 rcba;
if (likely(!asus_hides_smbus))
return;
WARN_ON(asus_rcba_base);
pci_read_config_dword(dev, 0xF0, &rcba);
/* use bits 31:14, 16 kB aligned */
asus_rcba_base = ioremap_nocache(rcba & 0xFFFFC000, 0x4000);
if (asus_rcba_base == NULL)
return;
}
static void asus_hides_smbus_lpc_ich6_resume_early(struct pci_dev *dev)
{
u32 val;
if (likely(!asus_hides_smbus || !asus_rcba_base))
return;
/* read the Function Disable register, dword mode only */
val = readl(asus_rcba_base + 0x3418);
writel(val & 0xFFFFFFF7, asus_rcba_base + 0x3418); /* enable the SMBus device */
}
static void asus_hides_smbus_lpc_ich6_resume(struct pci_dev *dev)
{
if (likely(!asus_hides_smbus || !asus_rcba_base))
return;
iounmap(asus_rcba_base);
asus_rcba_base = NULL;
dev_info(&dev->dev, "Enabled ICH6/i801 SMBus device\n");
}
static void asus_hides_smbus_lpc_ich6(struct pci_dev *dev)
{
asus_hides_smbus_lpc_ich6_suspend(dev);
asus_hides_smbus_lpc_ich6_resume_early(dev);
asus_hides_smbus_lpc_ich6_resume(dev);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6);
DECLARE_PCI_FIXUP_SUSPEND(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_suspend);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume_early);
/*
* SiS 96x south bridge: BIOS typically hides SMBus device...
*/
static void quirk_sis_96x_smbus(struct pci_dev *dev)
{
u8 val = 0;
pci_read_config_byte(dev, 0x77, &val);
if (val & 0x10) {
dev_info(&dev->dev, "Enabling SiS 96x SMBus\n");
pci_write_config_byte(dev, 0x77, val & ~0x10);
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus);
/*
* ... This is further complicated by the fact that some SiS96x south
* bridges pretend to be 85C503/5513 instead. In that case see if we
* spotted a compatible north bridge to make sure.
* (pci_find_device doesn't work yet)
*
* We can also enable the sis96x bit in the discovery register..
*/
#define SIS_DETECT_REGISTER 0x40
static void quirk_sis_503(struct pci_dev *dev)
{
u8 reg;
u16 devid;
pci_read_config_byte(dev, SIS_DETECT_REGISTER, &reg);
pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6));
pci_read_config_word(dev, PCI_DEVICE_ID, &devid);
if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) {
pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg);
return;
}
/*
* Ok, it now shows up as a 96x.. run the 96x quirk by
* hand in case it has already been processed.
* (depends on link order, which is apparently not guaranteed)
*/
dev->device = devid;
quirk_sis_96x_smbus(dev);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503);
/*
* On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller
* and MC97 modem controller are disabled when a second PCI soundcard is
* present. This patch, tweaking the VT8237 ISA bridge, enables them.
* -- bjd
*/
static void asus_hides_ac97_lpc(struct pci_dev *dev)
{
u8 val;
int asus_hides_ac97 = 0;
if (likely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) {
if (dev->device == PCI_DEVICE_ID_VIA_8237)
asus_hides_ac97 = 1;
}
if (!asus_hides_ac97)
return;
pci_read_config_byte(dev, 0x50, &val);
if (val & 0xc0) {
pci_write_config_byte(dev, 0x50, val & (~0xc0));
pci_read_config_byte(dev, 0x50, &val);
if (val & 0xc0)
dev_info(&dev->dev, "Onboard AC97/MC97 devices continue to play 'hide and seek'! 0x%x\n", val);
else
dev_info(&dev->dev, "Enabled onboard AC97/MC97 devices\n");
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc);
#if defined(CONFIG_ATA) || defined(CONFIG_ATA_MODULE)
/*
* If we are using libata we can drive this chip properly but must
* do this early on to make the additional device appear during
* the PCI scanning.
*/
static void quirk_jmicron_ata(struct pci_dev *pdev)
{
u32 conf1, conf5, class;
u8 hdr;
/* Only poke fn 0 */
if (PCI_FUNC(pdev->devfn))
return;
pci_read_config_dword(pdev, 0x40, &conf1);
pci_read_config_dword(pdev, 0x80, &conf5);
conf1 &= ~0x00CFF302; /* Clear bit 1, 8, 9, 12-19, 22, 23 */
conf5 &= ~(1 << 24); /* Clear bit 24 */
switch (pdev->device) {
case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */
case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */
case PCI_DEVICE_ID_JMICRON_JMB364: /* SATA dual ports */
/* The controller should be in single function ahci mode */
conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */
break;
case PCI_DEVICE_ID_JMICRON_JMB365:
case PCI_DEVICE_ID_JMICRON_JMB366:
/* Redirect IDE second PATA port to the right spot */
conf5 |= (1 << 24);
/* Fall through */
case PCI_DEVICE_ID_JMICRON_JMB361:
case PCI_DEVICE_ID_JMICRON_JMB363:
case PCI_DEVICE_ID_JMICRON_JMB369:
/* Enable dual function mode, AHCI on fn 0, IDE fn1 */
/* Set the class codes correctly and then direct IDE 0 */
conf1 |= 0x00C2A1B3; /* Set 0, 1, 4, 5, 7, 8, 13, 15, 17, 22, 23 */
break;
case PCI_DEVICE_ID_JMICRON_JMB368:
/* The controller should be in single function IDE mode */
conf1 |= 0x00C00000; /* Set 22, 23 */
break;
}
pci_write_config_dword(pdev, 0x40, conf1);
pci_write_config_dword(pdev, 0x80, conf5);
/* Update pdev accordingly */
pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr);
pdev->hdr_type = hdr & 0x7f;
pdev->multifunction = !!(hdr & 0x80);
pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class);
pdev->class = class >> 8;
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata);
#endif
#ifdef CONFIG_X86_IO_APIC
static void __init quirk_alder_ioapic(struct pci_dev *pdev)
{
int i;
if ((pdev->class >> 8) != 0xff00)
return;
/* the first BAR is the location of the IO APIC...we must
* not touch this (and it's already covered by the fixmap), so
* forcibly insert it into the resource tree */
if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0))
insert_resource(&iomem_resource, &pdev->resource[0]);
/* The next five BARs all seem to be rubbish, so just clean
* them out */
for (i=1; i < 6; i++) {
memset(&pdev->resource[i], 0, sizeof(pdev->resource[i]));
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic);
#endif
static void __devinit quirk_pcie_mch(struct pci_dev *pdev)
{
pci_msi_off(pdev);
pdev->no_msi = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch);
/*
* It's possible for the MSI to get corrupted if shpc and acpi
* are used together on certain PXH-based systems.
*/
static void __devinit quirk_pcie_pxh(struct pci_dev *dev)
{
pci_msi_off(dev);
dev->no_msi = 1;
dev_warn(&dev->dev, "PXH quirk detected; SHPC device MSI disabled\n");
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh);
/*
* Some Intel PCI Express chipsets have trouble with downstream
* device power management.
*/
static void quirk_intel_pcie_pm(struct pci_dev * dev)
{
pci_pm_d3_delay = 120;
dev->no_d1d2 = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2601, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2602, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2603, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2604, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2605, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2606, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2607, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2608, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2609, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm);
#ifdef CONFIG_X86_IO_APIC
/*
* Boot interrupts on some chipsets cannot be turned off. For these chipsets,
* remap the original interrupt in the linux kernel to the boot interrupt, so
* that a PCI device's interrupt handler is installed on the boot interrupt
* line instead.
*/
static void quirk_reroute_to_boot_interrupts_intel(struct pci_dev *dev)
{
if (noioapicquirk || noioapicreroute)
return;
dev->irq_reroute_variant = INTEL_IRQ_REROUTE_VARIANT;
dev_info(&dev->dev, "rerouting interrupts for [%04x:%04x]\n",
dev->vendor, dev->device);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel);
/*
* On some chipsets we can disable the generation of legacy INTx boot
* interrupts.
*/
/*
* IO-APIC1 on 6300ESB generates boot interrupts, see intel order no
* 300641-004US, section 5.7.3.
*/
#define INTEL_6300_IOAPIC_ABAR 0x40
#define INTEL_6300_DISABLE_BOOT_IRQ (1<<14)
static void quirk_disable_intel_boot_interrupt(struct pci_dev *dev)
{
u16 pci_config_word;
if (noioapicquirk)
return;
pci_read_config_word(dev, INTEL_6300_IOAPIC_ABAR, &pci_config_word);
pci_config_word |= INTEL_6300_DISABLE_BOOT_IRQ;
pci_write_config_word(dev, INTEL_6300_IOAPIC_ABAR, pci_config_word);
dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
dev->vendor, dev->device);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt);
/*
* disable boot interrupts on HT-1000
*/
#define BC_HT1000_FEATURE_REG 0x64
#define BC_HT1000_PIC_REGS_ENABLE (1<<0)
#define BC_HT1000_MAP_IDX 0xC00
#define BC_HT1000_MAP_DATA 0xC01
static void quirk_disable_broadcom_boot_interrupt(struct pci_dev *dev)
{
u32 pci_config_dword;
u8 irq;
if (noioapicquirk)
return;
pci_read_config_dword(dev, BC_HT1000_FEATURE_REG, &pci_config_dword);
pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword |
BC_HT1000_PIC_REGS_ENABLE);
for (irq = 0x10; irq < 0x10 + 32; irq++) {
outb(irq, BC_HT1000_MAP_IDX);
outb(0x00, BC_HT1000_MAP_DATA);
}
pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword);
dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
dev->vendor, dev->device);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt);
/*
* disable boot interrupts on AMD and ATI chipsets
*/
/*
* NOIOAMODE needs to be disabled to disable "boot interrupts". For AMD 8131
* rev. A0 and B0, NOIOAMODE needs to be disabled anyway to fix IO-APIC mode
* (due to an erratum).
*/
#define AMD_813X_MISC 0x40
#define AMD_813X_NOIOAMODE (1<<0)
#define AMD_813X_REV_B1 0x12
#define AMD_813X_REV_B2 0x13
static void quirk_disable_amd_813x_boot_interrupt(struct pci_dev *dev)
{
u32 pci_config_dword;
if (noioapicquirk)
return;
if ((dev->revision == AMD_813X_REV_B1) ||
(dev->revision == AMD_813X_REV_B2))
return;
pci_read_config_dword(dev, AMD_813X_MISC, &pci_config_dword);
pci_config_dword &= ~AMD_813X_NOIOAMODE;
pci_write_config_dword(dev, AMD_813X_MISC, pci_config_dword);
dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
dev->vendor, dev->device);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
#define AMD_8111_PCI_IRQ_ROUTING 0x56
static void quirk_disable_amd_8111_boot_interrupt(struct pci_dev *dev)
{
u16 pci_config_word;
if (noioapicquirk)
return;
pci_read_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, &pci_config_word);
if (!pci_config_word) {
dev_info(&dev->dev, "boot interrupts on device [%04x:%04x] "
"already disabled\n", dev->vendor, dev->device);
return;
}
pci_write_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, 0);
dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
dev->vendor, dev->device);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt);
DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt);
#endif /* CONFIG_X86_IO_APIC */
/*
* Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size
* but the PIO transfers won't work if BAR0 falls at the odd 8 bytes.
* Re-allocate the region if needed...
*/
static void __init quirk_tc86c001_ide(struct pci_dev *dev)
{
struct resource *r = &dev->resource[0];
if (r->start & 0x8) {
r->start = 0;
r->end = 0xf;
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA_2,
PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE,
quirk_tc86c001_ide);
static void __devinit quirk_netmos(struct pci_dev *dev)
{
unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4;
unsigned int num_serial = dev->subsystem_device & 0xf;
/*
* These Netmos parts are multiport serial devices with optional
* parallel ports. Even when parallel ports are present, they
* are identified as class SERIAL, which means the serial driver
* will claim them. To prevent this, mark them as class OTHER.
* These combo devices should be claimed by parport_serial.
*
* The subdevice ID is of the form 0x00PS, where <P> is the number
* of parallel ports and <S> is the number of serial ports.
*/
switch (dev->device) {
case PCI_DEVICE_ID_NETMOS_9835:
/* Well, this rule doesn't hold for the following 9835 device */
if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM &&
dev->subsystem_device == 0x0299)
return;
case PCI_DEVICE_ID_NETMOS_9735:
case PCI_DEVICE_ID_NETMOS_9745:
case PCI_DEVICE_ID_NETMOS_9845:
case PCI_DEVICE_ID_NETMOS_9855:
if (num_parallel) {
dev_info(&dev->dev, "Netmos %04x (%u parallel, "
"%u serial); changing class SERIAL to OTHER "
"(use parport_serial)\n",
dev->device, num_parallel, num_serial);
dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) |
(dev->class & 0xff);
}
}
}
DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID,
PCI_CLASS_COMMUNICATION_SERIAL, 8, quirk_netmos);
static void __devinit quirk_e100_interrupt(struct pci_dev *dev)
{
u16 command, pmcsr;
u8 __iomem *csr;
u8 cmd_hi;
int pm;
switch (dev->device) {
/* PCI IDs taken from drivers/net/e100.c */
case 0x1029:
case 0x1030 ... 0x1034:
case 0x1038 ... 0x103E:
case 0x1050 ... 0x1057:
case 0x1059:
case 0x1064 ... 0x106B:
case 0x1091 ... 0x1095:
case 0x1209:
case 0x1229:
case 0x2449:
case 0x2459:
case 0x245D:
case 0x27DC:
break;
default:
return;
}
/*
* Some firmware hands off the e100 with interrupts enabled,
* which can cause a flood of interrupts if packets are
* received before the driver attaches to the device. So
* disable all e100 interrupts here. The driver will
* re-enable them when it's ready.
*/
pci_read_config_word(dev, PCI_COMMAND, &command);
if (!(command & PCI_COMMAND_MEMORY) || !pci_resource_start(dev, 0))
return;
/*
* Check that the device is in the D0 power state. If it's not,
* there is no point to look any further.
*/
pm = pci_find_capability(dev, PCI_CAP_ID_PM);
if (pm) {
pci_read_config_word(dev, pm + PCI_PM_CTRL, &pmcsr);
if ((pmcsr & PCI_PM_CTRL_STATE_MASK) != PCI_D0)
return;
}
/* Convert from PCI bus to resource space. */
csr = ioremap(pci_resource_start(dev, 0), 8);
if (!csr) {
dev_warn(&dev->dev, "Can't map e100 registers\n");
return;
}
cmd_hi = readb(csr + 3);
if (cmd_hi == 0) {
dev_warn(&dev->dev, "Firmware left e100 interrupts enabled; "
"disabling\n");
writeb(1, csr + 3);
}
iounmap(csr);
}
DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
PCI_CLASS_NETWORK_ETHERNET, 8, quirk_e100_interrupt);
/*
* The 82575 and 82598 may experience data corruption issues when transitioning
* out of L0S. To prevent this we need to disable L0S on the pci-e link
*/
static void __devinit quirk_disable_aspm_l0s(struct pci_dev *dev)
{
dev_info(&dev->dev, "Disabling L0s\n");
pci_disable_link_state(dev, PCIE_LINK_STATE_L0S);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a7, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a9, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10b6, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c6, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c7, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c8, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10d6, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10db, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10dd, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10e1, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10ec, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f1, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f4, quirk_disable_aspm_l0s);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1508, quirk_disable_aspm_l0s);
static void __devinit fixup_rev1_53c810(struct pci_dev* dev)
{
/* rev 1 ncr53c810 chips don't set the class at all which means
* they don't get their resources remapped. Fix that here.
*/
if (dev->class == PCI_CLASS_NOT_DEFINED) {
dev_info(&dev->dev, "NCR 53c810 rev 1 detected; setting PCI class\n");
dev->class = PCI_CLASS_STORAGE_SCSI;
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
/* Enable 1k I/O space granularity on the Intel P64H2 */
static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
{
u16 en1k;
u8 io_base_lo, io_limit_lo;
unsigned long base, limit;
struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES;
pci_read_config_word(dev, 0x40, &en1k);
if (en1k & 0x200) {
dev_info(&dev->dev, "Enable I/O Space to 1KB granularity\n");
pci_read_config_byte(dev, PCI_IO_BASE, &io_base_lo);
pci_read_config_byte(dev, PCI_IO_LIMIT, &io_limit_lo);
base = (io_base_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8;
limit = (io_limit_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8;
if (base <= limit) {
res->start = base;
res->end = limit + 0x3ff;
}
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io);
/* Fix the IOBL_ADR for 1k I/O space granularity on the Intel P64H2
* The IOBL_ADR gets re-written to 4k boundaries in pci_setup_bridge()
* in drivers/pci/setup-bus.c
*/
static void __devinit quirk_p64h2_1k_io_fix_iobl(struct pci_dev *dev)
{
u16 en1k, iobl_adr, iobl_adr_1k;
struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES;
pci_read_config_word(dev, 0x40, &en1k);
if (en1k & 0x200) {
pci_read_config_word(dev, PCI_IO_BASE, &iobl_adr);
iobl_adr_1k = iobl_adr | (res->start >> 8) | (res->end & 0xfc00);
if (iobl_adr != iobl_adr_1k) {
dev_info(&dev->dev, "Fixing P64H2 IOBL_ADR from 0x%x to 0x%x for 1KB granularity\n",
iobl_adr,iobl_adr_1k);
pci_write_config_word(dev, PCI_IO_BASE, iobl_adr_1k);
}
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io_fix_iobl);
/* Under some circumstances, AER is not linked with extended capabilities.
* Force it to be linked by setting the corresponding control bit in the
* config space.
*/
static void quirk_nvidia_ck804_pcie_aer_ext_cap(struct pci_dev *dev)
{
uint8_t b;
if (pci_read_config_byte(dev, 0xf41, &b) == 0) {
if (!(b & 0x20)) {
pci_write_config_byte(dev, 0xf41, b | 0x20);
dev_info(&dev->dev,
"Linking AER extended capability\n");
}
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE,
quirk_nvidia_ck804_pcie_aer_ext_cap);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE,
quirk_nvidia_ck804_pcie_aer_ext_cap);
static void __devinit quirk_via_cx700_pci_parking_caching(struct pci_dev *dev)
{
/*
* Disable PCI Bus Parking and PCI Master read caching on CX700
* which causes unspecified timing errors with a VT6212L on the PCI
* bus leading to USB2.0 packet loss.
*
* This quirk is only enabled if a second (on the external PCI bus)
* VT6212L is found -- the CX700 core itself also contains a USB
* host controller with the same PCI ID as the VT6212L.
*/
/* Count VT6212L instances */
struct pci_dev *p = pci_get_device(PCI_VENDOR_ID_VIA,
PCI_DEVICE_ID_VIA_8235_USB_2, NULL);
uint8_t b;
/* p should contain the first (internal) VT6212L -- see if we have
an external one by searching again */
p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, p);
if (!p)
return;
pci_dev_put(p);
if (pci_read_config_byte(dev, 0x76, &b) == 0) {
if (b & 0x40) {
/* Turn off PCI Bus Parking */
pci_write_config_byte(dev, 0x76, b ^ 0x40);
dev_info(&dev->dev,
"Disabling VIA CX700 PCI parking\n");
}
}
if (pci_read_config_byte(dev, 0x72, &b) == 0) {
if (b != 0) {
/* Turn off PCI Master read caching */
pci_write_config_byte(dev, 0x72, 0x0);
/* Set PCI Master Bus time-out to "1x16 PCLK" */
pci_write_config_byte(dev, 0x75, 0x1);
/* Disable "Read FIFO Timer" */
pci_write_config_byte(dev, 0x77, 0x0);
dev_info(&dev->dev,
"Disabling VIA CX700 PCI caching\n");
}
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching);
/*
* For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
* VPD end tag will hang the device. This problem was initially
* observed when a vpd entry was created in sysfs
* ('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
* will dump 32k of data. Reading a full 32k will cause an access
* beyond the VPD end tag causing the device to hang. Once the device
* is hung, the bnx2 driver will not be able to reset the device.
* We believe that it is legal to read beyond the end tag and
* therefore the solution is to limit the read/write length.
*/
static void __devinit quirk_brcm_570x_limit_vpd(struct pci_dev *dev)
{
/*
* Only disable the VPD capability for 5706, 5706S, 5708,
* 5708S and 5709 rev. A
*/
if ((dev->device == PCI_DEVICE_ID_NX2_5706) ||
(dev->device == PCI_DEVICE_ID_NX2_5706S) ||
(dev->device == PCI_DEVICE_ID_NX2_5708) ||
(dev->device == PCI_DEVICE_ID_NX2_5708S) ||
((dev->device == PCI_DEVICE_ID_NX2_5709) &&
(dev->revision & 0xf0) == 0x0)) {
if (dev->vpd)
dev->vpd->len = 0x80;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_NX2_5706,
quirk_brcm_570x_limit_vpd);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_NX2_5706S,
quirk_brcm_570x_limit_vpd);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_NX2_5708,
quirk_brcm_570x_limit_vpd);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_NX2_5708S,
quirk_brcm_570x_limit_vpd);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_NX2_5709,
quirk_brcm_570x_limit_vpd);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_NX2_5709S,
quirk_brcm_570x_limit_vpd);
static void __devinit quirk_brcm_5719_limit_mrrs(struct pci_dev *dev)
{
u32 rev;
pci_read_config_dword(dev, 0xf4, &rev);
/* Only CAP the MRRS if the device is a 5719 A0 */
if (rev == 0x05719000) {
int readrq = pcie_get_readrq(dev);
if (readrq > 2048)
pcie_set_readrq(dev, 2048);
}
}
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_TIGON3_5719,
quirk_brcm_5719_limit_mrrs);
/* Originally in EDAC sources for i82875P:
* Intel tells BIOS developers to hide device 6 which
* configures the overflow device access containing
* the DRBs - this is where we expose device 6.
* http://www.x86-secret.com/articles/tweak/pat/patsecrets-2.htm
*/
static void __devinit quirk_unhide_mch_dev6(struct pci_dev *dev)
{
u8 reg;
if (pci_read_config_byte(dev, 0xF4, &reg) == 0 && !(reg & 0x02)) {
dev_info(&dev->dev, "Enabling MCH 'Overflow' Device\n");
pci_write_config_byte(dev, 0xF4, reg | 0x02);
}
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB,
quirk_unhide_mch_dev6);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB,
quirk_unhide_mch_dev6);
#ifdef CONFIG_TILE
/*
* The Tilera TILEmpower platform needs to set the link speed
* to 2.5GT(Giga-Transfers)/s (Gen 1). The default link speed
* setting is 5GT/s (Gen 2). 0x98 is the Link Control2 PCIe
* capability register of the PEX8624 PCIe switch. The switch
* supports link speed auto negotiation, but falsely sets
* the link speed to 5GT/s.
*/
static void __devinit quirk_tile_plx_gen1(struct pci_dev *dev)
{
if (tile_plx_gen1) {
pci_write_config_dword(dev, 0x98, 0x1);
mdelay(50);
}
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8624, quirk_tile_plx_gen1);
#endif /* CONFIG_TILE */
#ifdef CONFIG_PCI_MSI
/* Some chipsets do not support MSI. We cannot easily rely on setting
* PCI_BUS_FLAGS_NO_MSI in its bus flags because there are actually
* some other busses controlled by the chipset even if Linux is not
* aware of it. Instead of setting the flag on all busses in the
* machine, simply disable MSI globally.
*/
static void __init quirk_disable_all_msi(struct pci_dev *dev)
{
pci_no_msi();
dev_warn(&dev->dev, "MSI quirk detected; MSI disabled\n");
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS400_200, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS480, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3336, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3351, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3364, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8380_0, quirk_disable_all_msi);
/* Disable MSI on chipsets that are known to not support it */
static void __devinit quirk_disable_msi(struct pci_dev *dev)
{
if (dev->subordinate) {
dev_warn(&dev->dev, "MSI quirk detected; "
"subordinate MSI disabled\n");
dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0xa238, quirk_disable_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x5a3f, quirk_disable_msi);
/*
* The APC bridge device in AMD 780 family northbridges has some random
* OEM subsystem ID in its vendor ID register (erratum 18), so instead
* we use the possible vendor/device IDs of the host bridge for the
* declared quirk, and search for the APC bridge by slot number.
*/
static void __devinit quirk_amd_780_apc_msi(struct pci_dev *host_bridge)
{
struct pci_dev *apc_bridge;
apc_bridge = pci_get_slot(host_bridge->bus, PCI_DEVFN(1, 0));
if (apc_bridge) {
if (apc_bridge->device == 0x9602)
quirk_disable_msi(apc_bridge);
pci_dev_put(apc_bridge);
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9600, quirk_amd_780_apc_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9601, quirk_amd_780_apc_msi);
/* Go through the list of Hypertransport capabilities and
* return 1 if a HT MSI capability is found and enabled */
static int __devinit msi_ht_cap_enabled(struct pci_dev *dev)
{
int pos, ttl = 48;
pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
while (pos && ttl--) {
u8 flags;
if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
&flags) == 0)
{
dev_info(&dev->dev, "Found %s HT MSI Mapping\n",
flags & HT_MSI_FLAGS_ENABLE ?
"enabled" : "disabled");
return (flags & HT_MSI_FLAGS_ENABLE) != 0;
}
pos = pci_find_next_ht_capability(dev, pos,
HT_CAPTYPE_MSI_MAPPING);
}
return 0;
}
/* Check the hypertransport MSI mapping to know whether MSI is enabled or not */
static void __devinit quirk_msi_ht_cap(struct pci_dev *dev)
{
if (dev->subordinate && !msi_ht_cap_enabled(dev)) {
dev_warn(&dev->dev, "MSI quirk detected; "
"subordinate MSI disabled\n");
dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE,
quirk_msi_ht_cap);
/* The nVidia CK804 chipset may have 2 HT MSI mappings.
* MSI are supported if the MSI capability set in any of these mappings.
*/
static void __devinit quirk_nvidia_ck804_msi_ht_cap(struct pci_dev *dev)
{
struct pci_dev *pdev;
if (!dev->subordinate)
return;
/* check HT MSI cap on this chipset and the root one.
* a single one having MSI is enough to be sure that MSI are supported.
*/
pdev = pci_get_slot(dev->bus, 0);
if (!pdev)
return;
if (!msi_ht_cap_enabled(dev) && !msi_ht_cap_enabled(pdev)) {
dev_warn(&dev->dev, "MSI quirk detected; "
"subordinate MSI disabled\n");
dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI;
}
pci_dev_put(pdev);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE,
quirk_nvidia_ck804_msi_ht_cap);
/* Force enable MSI mapping capability on HT bridges */
static void __devinit ht_enable_msi_mapping(struct pci_dev *dev)
{
int pos, ttl = 48;
pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
while (pos && ttl--) {
u8 flags;
if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
&flags) == 0) {
dev_info(&dev->dev, "Enabling HT MSI Mapping\n");
pci_write_config_byte(dev, pos + HT_MSI_FLAGS,
flags | HT_MSI_FLAGS_ENABLE);
}
pos = pci_find_next_ht_capability(dev, pos,
HT_CAPTYPE_MSI_MAPPING);
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS,
PCI_DEVICE_ID_SERVERWORKS_HT1000_PXB,
ht_enable_msi_mapping);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE,
ht_enable_msi_mapping);
/* The P5N32-SLI motherboards from Asus have a problem with msi
* for the MCP55 NIC. It is not yet determined whether the msi problem
* also affects other devices. As for now, turn off msi for this device.
*/
static void __devinit nvenet_msi_disable(struct pci_dev *dev)
{
const char *board_name = dmi_get_system_info(DMI_BOARD_NAME);
if (board_name &&
(strstr(board_name, "P5N32-SLI PREMIUM") ||
strstr(board_name, "P5N32-E SLI"))) {
dev_info(&dev->dev,
"Disabling msi for MCP55 NIC on P5N32-SLI\n");
dev->no_msi = 1;
}
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
PCI_DEVICE_ID_NVIDIA_NVENET_15,
nvenet_msi_disable);
PCI: add quirk for non-symmetric-mode irq routing to versions 0 and 4 of the MCP55 northbridge A long time ago I worked on a RHEL5 bug in which kdump hung during boot on a set of systems. The systems hung because they never received timer interrupts during calibrate_delay. These systems also all had Opteron processors on a hypertransport bus, bridged to a pci bus via an Nvidia MCP55 northbridge chip. After much wrangling I managed to learn from Nvidia that they have an undocumented register in some versions of that chip which control how legacy interrupts are send to the cpu complex when the ioapic isn't active. Nvidia defaults this register to only send legacy interrupts to the BSP, so if kdump happens to boot on an AP, we never get timer interrupts and boom. I had initially used this quirk as a workaround, with my intent being to move apic initalization to an earlier point in the boot process, so the setting of the register would be irrelevant. Given the work involved in doing that however, the fragile nature of the apic initalization code, and the fact that, over the 2 years since we found this bug, the MCP55 is the only chip which seems to have this issue, I've figure at this point its likely safer to just carry the quirk around. By setting the referenced bits in this hidden register, interrupts will be broadcast to all cpus when the ioapic isn't active on the above described systems. Acked-by: Simon Horman <horms@verge.net.au> Acked-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-09-21 17:54:39 +00:00
/*
* Some versions of the MCP55 bridge from nvidia have a legacy irq routing
* config register. This register controls the routing of legacy interrupts
* from devices that route through the MCP55. If this register is misprogramed
* interrupts are only sent to the bsp, unlike conventional systems where the
* irq is broadxast to all online cpus. Not having this register set
* properly prevents kdump from booting up properly, so lets make sure that
* we have it set correctly.
* Note this is an undocumented register.
*/
static void __devinit nvbridge_check_legacy_irq_routing(struct pci_dev *dev)
{
u32 cfg;
if (!pci_find_capability(dev, PCI_CAP_ID_HT))
return;
PCI: add quirk for non-symmetric-mode irq routing to versions 0 and 4 of the MCP55 northbridge A long time ago I worked on a RHEL5 bug in which kdump hung during boot on a set of systems. The systems hung because they never received timer interrupts during calibrate_delay. These systems also all had Opteron processors on a hypertransport bus, bridged to a pci bus via an Nvidia MCP55 northbridge chip. After much wrangling I managed to learn from Nvidia that they have an undocumented register in some versions of that chip which control how legacy interrupts are send to the cpu complex when the ioapic isn't active. Nvidia defaults this register to only send legacy interrupts to the BSP, so if kdump happens to boot on an AP, we never get timer interrupts and boom. I had initially used this quirk as a workaround, with my intent being to move apic initalization to an earlier point in the boot process, so the setting of the register would be irrelevant. Given the work involved in doing that however, the fragile nature of the apic initalization code, and the fact that, over the 2 years since we found this bug, the MCP55 is the only chip which seems to have this issue, I've figure at this point its likely safer to just carry the quirk around. By setting the referenced bits in this hidden register, interrupts will be broadcast to all cpus when the ioapic isn't active on the above described systems. Acked-by: Simon Horman <horms@verge.net.au> Acked-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-09-21 17:54:39 +00:00
pci_read_config_dword(dev, 0x74, &cfg);
if (cfg & ((1 << 2) | (1 << 15))) {
printk(KERN_INFO "Rewriting irq routing register on MCP55\n");
cfg &= ~((1 << 2) | (1 << 15));
pci_write_config_dword(dev, 0x74, cfg);
}
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V0,
nvbridge_check_legacy_irq_routing);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V4,
nvbridge_check_legacy_irq_routing);
static int __devinit ht_check_msi_mapping(struct pci_dev *dev)
{
int pos, ttl = 48;
int found = 0;
/* check if there is HT MSI cap or enabled on this device */
pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
while (pos && ttl--) {
u8 flags;
if (found < 1)
found = 1;
if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
&flags) == 0) {
if (flags & HT_MSI_FLAGS_ENABLE) {
if (found < 2) {
found = 2;
break;
}
}
}
pos = pci_find_next_ht_capability(dev, pos,
HT_CAPTYPE_MSI_MAPPING);
}
return found;
}
static int __devinit host_bridge_with_leaf(struct pci_dev *host_bridge)
{
struct pci_dev *dev;
int pos;
int i, dev_no;
int found = 0;
dev_no = host_bridge->devfn >> 3;
for (i = dev_no + 1; i < 0x20; i++) {
dev = pci_get_slot(host_bridge->bus, PCI_DEVFN(i, 0));
if (!dev)
continue;
/* found next host bridge ?*/
pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE);
if (pos != 0) {
pci_dev_put(dev);
break;
}
if (ht_check_msi_mapping(dev)) {
found = 1;
pci_dev_put(dev);
break;
}
pci_dev_put(dev);
}
return found;
}
#define PCI_HT_CAP_SLAVE_CTRL0 4 /* link control */
#define PCI_HT_CAP_SLAVE_CTRL1 8 /* link control to */
static int __devinit is_end_of_ht_chain(struct pci_dev *dev)
{
int pos, ctrl_off;
int end = 0;
u16 flags, ctrl;
pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE);
if (!pos)
goto out;
pci_read_config_word(dev, pos + PCI_CAP_FLAGS, &flags);
ctrl_off = ((flags >> 10) & 1) ?
PCI_HT_CAP_SLAVE_CTRL0 : PCI_HT_CAP_SLAVE_CTRL1;
pci_read_config_word(dev, pos + ctrl_off, &ctrl);
if (ctrl & (1 << 6))
end = 1;
out:
return end;
}
static void __devinit nv_ht_enable_msi_mapping(struct pci_dev *dev)
{
struct pci_dev *host_bridge;
int pos;
int i, dev_no;
int found = 0;
dev_no = dev->devfn >> 3;
for (i = dev_no; i >= 0; i--) {
host_bridge = pci_get_slot(dev->bus, PCI_DEVFN(i, 0));
if (!host_bridge)
continue;
pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE);
if (pos != 0) {
found = 1;
break;
}
pci_dev_put(host_bridge);
}
if (!found)
return;
/* don't enable end_device/host_bridge with leaf directly here */
if (host_bridge == dev && is_end_of_ht_chain(host_bridge) &&
host_bridge_with_leaf(host_bridge))
goto out;
/* root did that ! */
if (msi_ht_cap_enabled(host_bridge))
goto out;
ht_enable_msi_mapping(dev);
out:
pci_dev_put(host_bridge);
}
static void __devinit ht_disable_msi_mapping(struct pci_dev *dev)
{
int pos, ttl = 48;
pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
while (pos && ttl--) {
u8 flags;
if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
&flags) == 0) {
dev_info(&dev->dev, "Disabling HT MSI Mapping\n");
pci_write_config_byte(dev, pos + HT_MSI_FLAGS,
flags & ~HT_MSI_FLAGS_ENABLE);
}
pos = pci_find_next_ht_capability(dev, pos,
HT_CAPTYPE_MSI_MAPPING);
}
}
static void __devinit __nv_msi_ht_cap_quirk(struct pci_dev *dev, int all)
{
struct pci_dev *host_bridge;
int pos;
int found;
if (!pci_msi_enabled())
return;
/* check if there is HT MSI cap or enabled on this device */
found = ht_check_msi_mapping(dev);
/* no HT MSI CAP */
if (found == 0)
return;
/*
* HT MSI mapping should be disabled on devices that are below
* a non-Hypertransport host bridge. Locate the host bridge...
*/
host_bridge = pci_get_bus_and_slot(0, PCI_DEVFN(0, 0));
if (host_bridge == NULL) {
dev_warn(&dev->dev,
"nv_msi_ht_cap_quirk didn't locate host bridge\n");
return;
}
pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE);
if (pos != 0) {
/* Host bridge is to HT */
if (found == 1) {
/* it is not enabled, try to enable it */
if (all)
ht_enable_msi_mapping(dev);
else
nv_ht_enable_msi_mapping(dev);
}
return;
}
/* HT MSI is not enabled */
if (found == 1)
return;
/* Host bridge is not to HT, disable HT MSI mapping on this device */
ht_disable_msi_mapping(dev);
}
static void __devinit nv_msi_ht_cap_quirk_all(struct pci_dev *dev)
{
return __nv_msi_ht_cap_quirk(dev, 1);
}
static void __devinit nv_msi_ht_cap_quirk_leaf(struct pci_dev *dev)
{
return __nv_msi_ht_cap_quirk(dev, 0);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all);
static void __devinit quirk_msi_intx_disable_bug(struct pci_dev *dev)
{
dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG;
}
static void __devinit quirk_msi_intx_disable_ati_bug(struct pci_dev *dev)
{
struct pci_dev *p;
/* SB700 MSI issue will be fixed at HW level from revision A21,
* we need check PCI REVISION ID of SMBus controller to get SB700
* revision.
*/
p = pci_get_device(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS,
NULL);
if (!p)
return;
if ((p->revision < 0x3B) && (p->revision >= 0x30))
dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG;
pci_dev_put(p);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_TIGON3_5780,
quirk_msi_intx_disable_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_TIGON3_5780S,
quirk_msi_intx_disable_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_TIGON3_5714,
quirk_msi_intx_disable_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_TIGON3_5714S,
quirk_msi_intx_disable_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_TIGON3_5715,
quirk_msi_intx_disable_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
PCI_DEVICE_ID_TIGON3_5715S,
quirk_msi_intx_disable_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4390,
quirk_msi_intx_disable_ati_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4391,
quirk_msi_intx_disable_ati_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4392,
quirk_msi_intx_disable_ati_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4393,
quirk_msi_intx_disable_ati_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4394,
quirk_msi_intx_disable_ati_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4373,
quirk_msi_intx_disable_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4374,
quirk_msi_intx_disable_bug);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4375,
quirk_msi_intx_disable_bug);
#endif /* CONFIG_PCI_MSI */
/* Allow manual resource allocation for PCI hotplug bridges
* via pci=hpmemsize=nnM and pci=hpiosize=nnM parameters. For
* some PCI-PCI hotplug bridges, like PLX 6254 (former HINT HB6),
* kernel fails to allocate resources when hotplug device is
* inserted and PCI bus is rescanned.
*/
static void __devinit quirk_hotplug_bridge(struct pci_dev *dev)
{
dev->is_hotplug_bridge = 1;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HINT, 0x0020, quirk_hotplug_bridge);
/*
* This is a quirk for the Ricoh MMC controller found as a part of
* some mulifunction chips.
* This is very similar and based on the ricoh_mmc driver written by
* Philip Langdale. Thank you for these magic sequences.
*
* These chips implement the four main memory card controllers (SD, MMC, MS, xD)
* and one or both of cardbus or firewire.
*
* It happens that they implement SD and MMC
* support as separate controllers (and PCI functions). The linux SDHCI
* driver supports MMC cards but the chip detects MMC cards in hardware
* and directs them to the MMC controller - so the SDHCI driver never sees
* them.
*
* To get around this, we must disable the useless MMC controller.
* At that point, the SDHCI controller will start seeing them
* It seems to be the case that the relevant PCI registers to deactivate the
* MMC controller live on PCI function 0, which might be the cardbus controller
* or the firewire controller, depending on the particular chip in question
*
* This has to be done early, because as soon as we disable the MMC controller
* other pci functions shift up one level, e.g. function #2 becomes function
* #1, and this will confuse the pci core.
*/
#ifdef CONFIG_MMC_RICOH_MMC
static void ricoh_mmc_fixup_rl5c476(struct pci_dev *dev)
{
/* disable via cardbus interface */
u8 write_enable;
u8 write_target;
u8 disable;
/* disable must be done via function #0 */
if (PCI_FUNC(dev->devfn))
return;
pci_read_config_byte(dev, 0xB7, &disable);
if (disable & 0x02)
return;
pci_read_config_byte(dev, 0x8E, &write_enable);
pci_write_config_byte(dev, 0x8E, 0xAA);
pci_read_config_byte(dev, 0x8D, &write_target);
pci_write_config_byte(dev, 0x8D, 0xB7);
pci_write_config_byte(dev, 0xB7, disable | 0x02);
pci_write_config_byte(dev, 0x8E, write_enable);
pci_write_config_byte(dev, 0x8D, write_target);
dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via cardbus function)\n");
dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n");
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476);
static void ricoh_mmc_fixup_r5c832(struct pci_dev *dev)
{
/* disable via firewire interface */
u8 write_enable;
u8 disable;
/* disable must be done via function #0 */
if (PCI_FUNC(dev->devfn))
return;
/*
* RICOH 0xe823 SD/MMC card reader fails to recognize
* certain types of SD/MMC cards. Lowering the SD base
* clock frequency from 200Mhz to 50Mhz fixes this issue.
*
* 0x150 - SD2.0 mode enable for changing base clock
* frequency to 50Mhz
* 0xe1 - Base clock frequency
* 0x32 - 50Mhz new clock frequency
* 0xf9 - Key register for 0x150
* 0xfc - key register for 0xe1
*/
if (dev->device == PCI_DEVICE_ID_RICOH_R5CE823) {
pci_write_config_byte(dev, 0xf9, 0xfc);
pci_write_config_byte(dev, 0x150, 0x10);
pci_write_config_byte(dev, 0xf9, 0x00);
pci_write_config_byte(dev, 0xfc, 0x01);
pci_write_config_byte(dev, 0xe1, 0x32);
pci_write_config_byte(dev, 0xfc, 0x00);
dev_notice(&dev->dev, "MMC controller base frequency changed to 50Mhz.\n");
}
pci_read_config_byte(dev, 0xCB, &disable);
if (disable & 0x02)
return;
pci_read_config_byte(dev, 0xCA, &write_enable);
pci_write_config_byte(dev, 0xCA, 0x57);
pci_write_config_byte(dev, 0xCB, disable | 0x02);
pci_write_config_byte(dev, 0xCA, write_enable);
dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via firewire function)\n");
dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n");
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832);
#endif /*CONFIG_MMC_RICOH_MMC*/
#ifdef CONFIG_DMAR_TABLE
#define VTUNCERRMSK_REG 0x1ac
#define VTD_MSK_SPEC_ERRORS (1 << 31)
/*
* This is a quirk for masking vt-d spec defined errors to platform error
* handling logic. With out this, platforms using Intel 7500, 5500 chipsets
* (and the derivative chipsets like X58 etc) seem to generate NMI/SMI (based
* on the RAS config settings of the platform) when a vt-d fault happens.
* The resulting SMI caused the system to hang.
*
* VT-d spec related errors are already handled by the VT-d OS code, so no
* need to report the same error through other channels.
*/
static void vtd_mask_spec_errors(struct pci_dev *dev)
{
u32 word;
pci_read_config_dword(dev, VTUNCERRMSK_REG, &word);
pci_write_config_dword(dev, VTUNCERRMSK_REG, word | VTD_MSK_SPEC_ERRORS);
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x342e, vtd_mask_spec_errors);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x3c28, vtd_mask_spec_errors);
#endif
static void __devinit fixup_ti816x_class(struct pci_dev* dev)
{
/* TI 816x devices do not have class code set when in PCIe boot mode */
dev_info(&dev->dev, "Setting PCI class for 816x PCIe device\n");
dev->class = PCI_CLASS_MULTIMEDIA_VIDEO;
}
DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_TI, 0xb800,
PCI_CLASS_NOT_DEFINED, 0, fixup_ti816x_class);
/* Some PCIe devices do not work reliably with the claimed maximum
* payload size supported.
*/
static void __devinit fixup_mpss_256(struct pci_dev *dev)
{
dev->pcie_mpss = 1; /* 256 bytes */
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE,
PCI_DEVICE_ID_SOLARFLARE_SFC4000A_0, fixup_mpss_256);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE,
PCI_DEVICE_ID_SOLARFLARE_SFC4000A_1, fixup_mpss_256);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE,
PCI_DEVICE_ID_SOLARFLARE_SFC4000B, fixup_mpss_256);
/* Intel 5000 and 5100 Memory controllers have an errata with read completion
* coalescing (which is enabled by default on some BIOSes) and MPS of 256B.
* Since there is no way of knowing what the PCIE MPS on each fabric will be
* until all of the devices are discovered and buses walked, read completion
* coalescing must be disabled. Unfortunately, it cannot be re-enabled because
* it is possible to hotplug a device with MPS of 256B.
*/
static void __devinit quirk_intel_mc_errata(struct pci_dev *dev)
{
int err;
u16 rcc;
if (pcie_bus_config == PCIE_BUS_TUNE_OFF)
return;
/* Intel errata specifies bits to change but does not say what they are.
* Keeping them magical until such time as the registers and values can
* be explained.
*/
err = pci_read_config_word(dev, 0x48, &rcc);
if (err) {
dev_err(&dev->dev, "Error attempting to read the read "
"completion coalescing register.\n");
return;
}
if (!(rcc & (1 << 10)))
return;
rcc &= ~(1 << 10);
err = pci_write_config_word(dev, 0x48, rcc);
if (err) {
dev_err(&dev->dev, "Error attempting to write the read "
"completion coalescing register.\n");
return;
}
pr_info_once("Read completion coalescing disabled due to hardware "
"errata relating to 256B MPS.\n");
}
/* Intel 5000 series memory controllers and ports 2-7 */
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25c0, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d0, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d4, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d8, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_mc_errata);
/* Intel 5100 series memory controllers and ports 2-7 */
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65c0, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e2, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e3, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e4, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e5, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e6, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e7, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f7, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f8, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f9, quirk_intel_mc_errata);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65fa, quirk_intel_mc_errata);
static void do_one_fixup_debug(void (*fn)(struct pci_dev *dev), struct pci_dev *dev)
{
ktime_t calltime, delta, rettime;
unsigned long long duration;
printk(KERN_DEBUG "calling %pF @ %i for %s\n",
fn, task_pid_nr(current), dev_name(&dev->dev));
calltime = ktime_get();
fn(dev);
rettime = ktime_get();
delta = ktime_sub(rettime, calltime);
duration = (unsigned long long) ktime_to_ns(delta) >> 10;
printk(KERN_DEBUG "pci fixup %pF returned after %lld usecs for %s\n",
fn, duration, dev_name(&dev->dev));
}
/*
* Some BIOS implementations leave the Intel GPU interrupts enabled,
* even though no one is handling them (f.e. i915 driver is never loaded).
* Additionally the interrupt destination is not set up properly
* and the interrupt ends up -somewhere-.
*
* These spurious interrupts are "sticky" and the kernel disables
* the (shared) interrupt line after 100.000+ generated interrupts.
*
* Fix it by disabling the still enabled interrupts.
* This resolves crashes often seen on monitor unplug.
*/
#define I915_DEIER_REG 0x4400c
static void __devinit disable_igfx_irq(struct pci_dev *dev)
{
void __iomem *regs = pci_iomap(dev, 0, 0);
if (regs == NULL) {
dev_warn(&dev->dev, "igfx quirk: Can't iomap PCI device\n");
return;
}
/* Check if any interrupt line is still enabled */
if (readl(regs + I915_DEIER_REG) != 0) {
dev_warn(&dev->dev, "BIOS left Intel GPU interrupts enabled; "
"disabling\n");
writel(0, regs + I915_DEIER_REG);
}
pci_iounmap(dev, regs);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0102, disable_igfx_irq);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x010a, disable_igfx_irq);
static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f,
struct pci_fixup *end)
{
for (; f < end; f++)
if ((f->class == (u32) (dev->class >> f->class_shift) ||
f->class == (u32) PCI_ANY_ID) &&
(f->vendor == dev->vendor ||
f->vendor == (u16) PCI_ANY_ID) &&
(f->device == dev->device ||
f->device == (u16) PCI_ANY_ID)) {
dev_dbg(&dev->dev, "calling %pF\n", f->hook);
if (initcall_debug)
do_one_fixup_debug(f->hook, dev);
else
f->hook(dev);
}
}
extern struct pci_fixup __start_pci_fixups_early[];
extern struct pci_fixup __end_pci_fixups_early[];
extern struct pci_fixup __start_pci_fixups_header[];
extern struct pci_fixup __end_pci_fixups_header[];
extern struct pci_fixup __start_pci_fixups_final[];
extern struct pci_fixup __end_pci_fixups_final[];
extern struct pci_fixup __start_pci_fixups_enable[];
extern struct pci_fixup __end_pci_fixups_enable[];
extern struct pci_fixup __start_pci_fixups_resume[];
extern struct pci_fixup __end_pci_fixups_resume[];
extern struct pci_fixup __start_pci_fixups_resume_early[];
extern struct pci_fixup __end_pci_fixups_resume_early[];
extern struct pci_fixup __start_pci_fixups_suspend[];
extern struct pci_fixup __end_pci_fixups_suspend[];
void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev)
{
struct pci_fixup *start, *end;
switch(pass) {
case pci_fixup_early:
start = __start_pci_fixups_early;
end = __end_pci_fixups_early;
break;
case pci_fixup_header:
start = __start_pci_fixups_header;
end = __end_pci_fixups_header;
break;
case pci_fixup_final:
start = __start_pci_fixups_final;
end = __end_pci_fixups_final;
break;
case pci_fixup_enable:
start = __start_pci_fixups_enable;
end = __end_pci_fixups_enable;
break;
case pci_fixup_resume:
start = __start_pci_fixups_resume;
end = __end_pci_fixups_resume;
break;
case pci_fixup_resume_early:
start = __start_pci_fixups_resume_early;
end = __end_pci_fixups_resume_early;
break;
case pci_fixup_suspend:
start = __start_pci_fixups_suspend;
end = __end_pci_fixups_suspend;
break;
default:
/* stupid compiler warning, you would think with an enum... */
return;
}
pci_do_fixups(dev, start, end);
}
EXPORT_SYMBOL(pci_fixup_device);
static int __init pci_apply_final_quirks(void)
{
struct pci_dev *dev = NULL;
u8 cls = 0;
u8 tmp;
if (pci_cache_line_size)
printk(KERN_DEBUG "PCI: CLS %u bytes\n",
pci_cache_line_size << 2);
for_each_pci_dev(dev) {
pci_fixup_device(pci_fixup_final, dev);
/*
* If arch hasn't set it explicitly yet, use the CLS
* value shared by all PCI devices. If there's a
* mismatch, fall back to the default value.
*/
if (!pci_cache_line_size) {
pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &tmp);
if (!cls)
cls = tmp;
if (!tmp || cls == tmp)
continue;
printk(KERN_DEBUG "PCI: CLS mismatch (%u != %u), "
"using %u bytes\n", cls << 2, tmp << 2,
pci_dfl_cache_line_size << 2);
pci_cache_line_size = pci_dfl_cache_line_size;
}
}
if (!pci_cache_line_size) {
printk(KERN_DEBUG "PCI: CLS %u bytes, default %u\n",
cls << 2, pci_dfl_cache_line_size << 2);
pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size;
}
return 0;
}
fs_initcall_sync(pci_apply_final_quirks);
/*
* Followings are device-specific reset methods which can be used to
* reset a single function if other methods (e.g. FLR, PM D0->D3) are
* not available.
*/
static int reset_intel_generic_dev(struct pci_dev *dev, int probe)
{
int pos;
/* only implement PCI_CLASS_SERIAL_USB at present */
if (dev->class == PCI_CLASS_SERIAL_USB) {
pos = pci_find_capability(dev, PCI_CAP_ID_VNDR);
if (!pos)
return -ENOTTY;
if (probe)
return 0;
pci_write_config_byte(dev, pos + 0x4, 1);
msleep(100);
return 0;
} else {
return -ENOTTY;
}
}
static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, int probe)
{
int pos;
pos = pci_find_capability(dev, PCI_CAP_ID_EXP);
if (!pos)
return -ENOTTY;
if (probe)
return 0;
pci_write_config_word(dev, pos + PCI_EXP_DEVCTL,
PCI_EXP_DEVCTL_BCR_FLR);
msleep(100);
return 0;
}
#define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed
static const struct pci_dev_reset_methods pci_dev_reset_methods[] = {
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF,
reset_intel_82599_sfp_virtfn },
{ PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
reset_intel_generic_dev },
{ 0 }
};
int pci_dev_specific_reset(struct pci_dev *dev, int probe)
{
const struct pci_dev_reset_methods *i;
for (i = pci_dev_reset_methods; i->reset; i++) {
if ((i->vendor == dev->vendor ||
i->vendor == (u16)PCI_ANY_ID) &&
(i->device == dev->device ||
i->device == (u16)PCI_ANY_ID))
return i->reset(dev, probe);
}
return -ENOTTY;
}