linux/drivers/mmc/core/sd_ops.c

351 lines
6.9 KiB
C
Raw Normal View History

/*
* linux/drivers/mmc/core/sd_ops.h
*
* Copyright 2006-2007 Pierre Ossman
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or (at
* your option) any later version.
*/
#include <linux/types.h>
#include <linux/scatterlist.h>
#include <linux/mmc/host.h>
#include <linux/mmc/card.h>
#include <linux/mmc/mmc.h>
#include <linux/mmc/sd.h>
#include "core.h"
#include "sd_ops.h"
static int mmc_app_cmd(struct mmc_host *host, struct mmc_card *card)
{
int err;
struct mmc_command cmd;
BUG_ON(!host);
BUG_ON(card && (card->host != host));
cmd.opcode = MMC_APP_CMD;
if (card) {
cmd.arg = card->rca << 16;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
} else {
cmd.arg = 0;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_BCR;
}
err = mmc_wait_for_cmd(host, &cmd, 0);
if (err)
return err;
/* Check that card supported application commands */
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
if (!mmc_host_is_spi(host) && !(cmd.resp[0] & R1_APP_CMD))
return -EOPNOTSUPP;
return 0;
}
/**
* mmc_wait_for_app_cmd - start an application command and wait for
completion
* @host: MMC host to start command
* @card: Card to send MMC_APP_CMD to
* @cmd: MMC command to start
* @retries: maximum number of retries
*
* Sends a MMC_APP_CMD, checks the card response, sends the command
* in the parameter and waits for it to complete. Return any error
* that occurred while the command was executing. Do not attempt to
* parse the response.
*/
int mmc_wait_for_app_cmd(struct mmc_host *host, struct mmc_card *card,
struct mmc_command *cmd, int retries)
{
struct mmc_request mrq;
int i, err;
BUG_ON(!cmd);
BUG_ON(retries < 0);
err = -EIO;
/*
* We have to resend MMC_APP_CMD for each attempt so
* we cannot use the retries field in mmc_command.
*/
for (i = 0;i <= retries;i++) {
memset(&mrq, 0, sizeof(struct mmc_request));
err = mmc_app_cmd(host, card);
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
if (err) {
/* no point in retrying; no APP commands allowed */
if (mmc_host_is_spi(host)) {
if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
break;
}
continue;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
}
memset(&mrq, 0, sizeof(struct mmc_request));
memset(cmd->resp, 0, sizeof(cmd->resp));
cmd->retries = 0;
mrq.cmd = cmd;
cmd->data = NULL;
mmc_wait_for_req(host, &mrq);
err = cmd->error;
if (!cmd->error)
break;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
/* no point in retrying illegal APP commands */
if (mmc_host_is_spi(host)) {
if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
break;
}
}
return err;
}
EXPORT_SYMBOL(mmc_wait_for_app_cmd);
int mmc_app_set_bus_width(struct mmc_card *card, int width)
{
int err;
struct mmc_command cmd;
BUG_ON(!card);
BUG_ON(!card->host);
memset(&cmd, 0, sizeof(struct mmc_command));
cmd.opcode = SD_APP_SET_BUS_WIDTH;
cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
switch (width) {
case MMC_BUS_WIDTH_1:
cmd.arg = SD_BUS_WIDTH_1;
break;
case MMC_BUS_WIDTH_4:
cmd.arg = SD_BUS_WIDTH_4;
break;
default:
return -EINVAL;
}
err = mmc_wait_for_app_cmd(card->host, card, &cmd, MMC_CMD_RETRIES);
if (err)
return err;
return 0;
}
int mmc_send_app_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
{
struct mmc_command cmd;
int i, err = 0;
BUG_ON(!host);
memset(&cmd, 0, sizeof(struct mmc_command));
cmd.opcode = SD_APP_OP_COND;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
if (mmc_host_is_spi(host))
cmd.arg = ocr & (1 << 30); /* SPI only defines one bit */
else
cmd.arg = ocr;
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R3 | MMC_CMD_BCR;
for (i = 100; i; i--) {
err = mmc_wait_for_app_cmd(host, NULL, &cmd, MMC_CMD_RETRIES);
if (err)
break;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
/* if we're just probing, do a single pass */
if (ocr == 0)
break;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
/* otherwise wait until reset completes */
if (mmc_host_is_spi(host)) {
if (!(cmd.resp[0] & R1_SPI_IDLE))
break;
} else {
if (cmd.resp[0] & MMC_CARD_BUSY)
break;
}
err = -ETIMEDOUT;
mmc_delay(10);
}
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
if (rocr && !mmc_host_is_spi(host))
*rocr = cmd.resp[0];
return err;
}
int mmc_send_if_cond(struct mmc_host *host, u32 ocr)
{
struct mmc_command cmd;
int err;
static const u8 test_pattern = 0xAA;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
u8 result_pattern;
/*
* To support SD 2.0 cards, we must always invoke SD_SEND_IF_COND
* before SD_APP_OP_COND. This command will harmlessly fail for
* SD 1.0 cards.
*/
cmd.opcode = SD_SEND_IF_COND;
cmd.arg = ((ocr & 0xFF8000) != 0) << 8 | test_pattern;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
cmd.flags = MMC_RSP_SPI_R7 | MMC_RSP_R7 | MMC_CMD_BCR;
err = mmc_wait_for_cmd(host, &cmd, 0);
if (err)
return err;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
if (mmc_host_is_spi(host))
result_pattern = cmd.resp[1] & 0xFF;
else
result_pattern = cmd.resp[0] & 0xFF;
if (result_pattern != test_pattern)
return -EIO;
return 0;
}
int mmc_send_relative_addr(struct mmc_host *host, unsigned int *rca)
{
int err;
struct mmc_command cmd;
BUG_ON(!host);
BUG_ON(!rca);
memset(&cmd, 0, sizeof(struct mmc_command));
cmd.opcode = SD_SEND_RELATIVE_ADDR;
cmd.arg = 0;
cmd.flags = MMC_RSP_R6 | MMC_CMD_BCR;
err = mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
if (err)
return err;
*rca = cmd.resp[0] >> 16;
return 0;
}
int mmc_app_send_scr(struct mmc_card *card, u32 *scr)
{
int err;
struct mmc_request mrq;
struct mmc_command cmd;
struct mmc_data data;
struct scatterlist sg;
BUG_ON(!card);
BUG_ON(!card->host);
BUG_ON(!scr);
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
/* NOTE: caller guarantees scr is heap-allocated */
err = mmc_app_cmd(card->host, card);
if (err)
return err;
memset(&mrq, 0, sizeof(struct mmc_request));
memset(&cmd, 0, sizeof(struct mmc_command));
memset(&data, 0, sizeof(struct mmc_data));
mrq.cmd = &cmd;
mrq.data = &data;
cmd.opcode = SD_APP_SEND_SCR;
cmd.arg = 0;
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
data.blksz = 8;
data.blocks = 1;
data.flags = MMC_DATA_READ;
data.sg = &sg;
data.sg_len = 1;
sg_init_one(&sg, scr, 8);
mmc_set_data_timeout(&data, card);
mmc_wait_for_req(card->host, &mrq);
if (cmd.error)
return cmd.error;
if (data.error)
return data.error;
scr[0] = be32_to_cpu(scr[0]);
scr[1] = be32_to_cpu(scr[1]);
return 0;
}
int mmc_sd_switch(struct mmc_card *card, int mode, int group,
u8 value, u8 *resp)
{
struct mmc_request mrq;
struct mmc_command cmd;
struct mmc_data data;
struct scatterlist sg;
BUG_ON(!card);
BUG_ON(!card->host);
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
/* NOTE: caller guarantees resp is heap-allocated */
mode = !!mode;
value &= 0xF;
memset(&mrq, 0, sizeof(struct mmc_request));
memset(&cmd, 0, sizeof(struct mmc_command));
memset(&data, 0, sizeof(struct mmc_data));
mrq.cmd = &cmd;
mrq.data = &data;
cmd.opcode = SD_SWITCH;
cmd.arg = mode << 31 | 0x00FFFFFF;
cmd.arg &= ~(0xF << (group * 4));
cmd.arg |= value << (group * 4);
MMC core learns about SPI Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
data.blksz = 64;
data.blocks = 1;
data.flags = MMC_DATA_READ;
data.sg = &sg;
data.sg_len = 1;
sg_init_one(&sg, resp, 64);
mmc_set_data_timeout(&data, card);
mmc_wait_for_req(card->host, &mrq);
if (cmd.error)
return cmd.error;
if (data.error)
return data.error;
return 0;
}