linux/drivers/dma/Makefile

26 lines
843 B
Makefile
Raw Normal View History

ifeq ($(CONFIG_DMADEVICES_DEBUG),y)
EXTRA_CFLAGS += -DDEBUG
endif
ifeq ($(CONFIG_DMADEVICES_VDEBUG),y)
EXTRA_CFLAGS += -DVERBOSE_DEBUG
endif
obj-$(CONFIG_DMA_ENGINE) += dmaengine.o
obj-$(CONFIG_NET_DMA) += iovlock.o
obj-$(CONFIG_DMATEST) += dmatest.o
obj-$(CONFIG_INTEL_IOATDMA) += ioat/
dmaengine: driver for the iop32x, iop33x, and iop13xx raid engines The Intel(R) IOP series of i/o processors integrate an Xscale core with raid acceleration engines. The capabilities per platform are: iop219: (2) copy engines iop321: (2) copy engines (1) xor and block fill engine iop33x: (2) copy and crc32c engines (1) xor, xor zero sum, pq, pq zero sum, and block fill engine iop34x (iop13xx): (2) copy, crc32c, xor, xor zero sum, and block fill engines (1) copy, crc32c, xor, xor zero sum, pq, pq zero sum, and block fill engine The driver supports the features of the async_tx api: * asynchronous notification of operation completion * implicit (interupt triggered) handling of inter-channel transaction dependencies The driver adapts to the platform it is running by two methods. 1/ #include <asm/arch/adma.h> which defines the hardware specific iop_chan_* and iop_desc_* routines as a series of static inline functions 2/ The private platform data attached to the platform_device defines the capabilities of the channels 20070626: Callbacks are run in a tasklet. Given the recent discussion on LKML about killing tasklets in favor of workqueues I did a quick conversion of the driver. Raid5 resync performance dropped from 50MB/s to 30MB/s, so the tasklet implementation remains until a generic softirq interface is available. Changelog: * fixed a slot allocation bug in do_iop13xx_adma_xor that caused too few slots to be requested eventually leading to data corruption * enabled the slot allocation routine to attempt to free slots before returning -ENOMEM * switched the cleanup routine to solely use the software chain and the status register to determine if a descriptor is complete. This is necessary to support other IOP engines that do not have status writeback capability * make the driver iop generic * modified the allocation routines to understand allocating a group of slots for a single operation * added a null xor initialization operation for the xor only channel on iop3xx * support xor operations on buffers larger than the hardware maximum * split the do_* routines into separate prep, src/dest set, submit stages * added async_tx support (dependent operations initiation at cleanup time) * simplified group handling * added interrupt support (callbacks via tasklets) * brought the pending depth inline with ioat (i.e. 4 descriptors) * drop dma mapping methods, suggested by Chris Leech * don't use inline in C files, Adrian Bunk * remove static tasklet declarations * make iop_adma_alloc_slots easier to read and remove chances for a corrupted descriptor chain * fix locking bug in iop_adma_alloc_chan_resources, Benjamin Herrenschmidt * convert capabilities over to dma_cap_mask_t * fixup sparse warnings * add descriptor flush before iop_chan_enable * checkpatch.pl fixes * gpl v2 only correction * move set_src, set_dest, submit to async_tx methods * move group_list and phys to async_tx Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2007-01-02 20:52:26 +00:00
obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o
obj-$(CONFIG_FSL_DMA) += fsldma.o
obj-$(CONFIG_MPC512X_DMA) += mpc512x_dma.o
obj-$(CONFIG_MV_XOR) += mv_xor.o
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
obj-$(CONFIG_DW_DMAC) += dw_dmac.o
obj-$(CONFIG_AT_HDMAC) += at_hdmac.o
obj-$(CONFIG_MX3_IPU) += ipu/
obj-$(CONFIG_TXX9_DMAC) += txx9dmac.o
obj-$(CONFIG_SH_DMAE) += shdma.o
obj-$(CONFIG_COH901318) += coh901318.o coh901318_lli.o
obj-$(CONFIG_AMCC_PPC440SPE_ADMA) += ppc4xx/
obj-$(CONFIG_TIMB_DMA) += timb_dma.o
obj-$(CONFIG_STE_DMA40) += ste_dma40.o ste_dma40_ll.o
obj-$(CONFIG_PL330_DMA) += pl330.o