Updated SF41/SF45 patch to use multiple for center offset. New Marlin firmware requires this.
Updated start.gcode to match this requirement.master
parent
e238a849a3
commit
4fe5009351
23
patches/41
23
patches/41
|
@ -182,7 +182,7 @@
|
|||
+
|
||||
--- ori/41/skeinforge_application/alterations/start.gcode
|
||||
+++ target/SF41/skeinforge_application/alterations/start.gcode
|
||||
@@ -0,0 +1,30 @@
|
||||
@@ -0,0 +1,31 @@
|
||||
+(start of start.txt)
|
||||
+M92 E926.5 (the number of extruder steps to take in 1mm of filament)
|
||||
+G21 (metric values)
|
||||
|
@ -191,25 +191,26 @@
|
|||
+G21
|
||||
+G90 (absolute positioning)
|
||||
+G21
|
||||
+G28 (move X/Y/Z to min endstops)
|
||||
+G28 X0 Y0 (move X/Y to min endstops)
|
||||
+G28 Z0 (move Z to min endstops)
|
||||
+G21
|
||||
+G21 ( if your prints start too high, try changing the Z0.0 below )
|
||||
+G21 ( to Z1.0 - the number after the Z is the actual, physical )
|
||||
+G21 ( height of the nozzle in mm. This can take some messing around )
|
||||
+G21 ( with to get just right... )
|
||||
+G21
|
||||
+G92 X-105 Y-105 Z0.0 E0 (reset software position to front/left/z=0.0)
|
||||
+G92 X0 Y0 Z0 E0 (reset software position to front/left/z=0.0)
|
||||
+G21
|
||||
+G1 Z15.0 F400 (move the platform down 15mm)
|
||||
+G1 X0 Y0 F3500 (go to the middle of the platform)
|
||||
+G92 E0 (zero the extruded length)
|
||||
+G21
|
||||
+G1 F75 E15 (extrude 15mm of feed stock)
|
||||
+G1 F75 E13.5 (reverse feed stock by 1.5mm)
|
||||
+G1 F75 E5 (extrude 5mm of feed stock)
|
||||
+G1 F75 E3.5 (reverse feed stock by 1.5mm)
|
||||
+G92 E0 (zero the extruded length again)
|
||||
+G21
|
||||
+M1 (Clean the nozzle then press YES to continue...)
|
||||
+G21
|
||||
+G1 X100 Y100 F3500 (go to the middle of the platform)
|
||||
+G1 Z0.0 F400 (back to Z=0 and start the print!)
|
||||
+(end of start.txt)
|
||||
+
|
||||
|
@ -569,7 +570,7 @@
|
|||
self.executeTitle = 'Limit'
|
||||
--- ori/41/skeinforge_application/skeinforge_plugins/craft_plugins/multiply.py
|
||||
+++ target/SF41/skeinforge_application/skeinforge_plugins/craft_plugins/multiply.py
|
||||
@@ -105,7 +105,7 @@
|
||||
@@ -105,11 +105,11 @@
|
||||
self.fileNameInput = settings.FileNameInput().getFromFileName(
|
||||
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Multiply', self, '')
|
||||
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute('http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Multiply')
|
||||
|
@ -577,7 +578,13 @@
|
|||
+ self.activateMultiply = settings.BooleanSetting().getFromValue('Activate Multiply:', self, True )
|
||||
settings.LabelSeparator().getFromRepository(self)
|
||||
settings.LabelDisplay().getFromName('- Center -', self )
|
||||
self.centerX = settings.FloatSpin().getFromValue(-100.0, 'Center X (mm):', self, 100.0, 0.0)
|
||||
- self.centerX = settings.FloatSpin().getFromValue(-100.0, 'Center X (mm):', self, 100.0, 0.0)
|
||||
- self.centerY = settings.FloatSpin().getFromValue(-100.0, 'Center Y (mm):', self, 100.0, 0.0)
|
||||
+ self.centerX = settings.FloatSpin().getFromValue(-100.0, 'Center X (mm):', self, 100.0, 105.0)
|
||||
+ self.centerY = settings.FloatSpin().getFromValue(-100.0, 'Center Y (mm):', self, 100.0, 105.0)
|
||||
settings.LabelSeparator().getFromRepository(self)
|
||||
settings.LabelDisplay().getFromName('- Number of Cells -', self)
|
||||
self.numberOfColumns = settings.IntSpin().getFromValue(1, 'Number of Columns (integer):', self, 10, 1)
|
||||
--- ori/41/skeinforge_application/skeinforge_plugins/craft_plugins/raft.py
|
||||
+++ target/SF41/skeinforge_application/skeinforge_plugins/craft_plugins/raft.py
|
||||
@@ -358,7 +358,7 @@
|
||||
|
|
23
patches/45
23
patches/45
|
@ -35,7 +35,7 @@
|
|||
+
|
||||
--- ori/45/skeinforge_application/alterations/start.gcode
|
||||
+++ target/SF45/skeinforge_application/alterations/start.gcode
|
||||
@@ -0,0 +1,30 @@
|
||||
@@ -0,0 +1,31 @@
|
||||
+(start of start.txt)
|
||||
+M92 E926.5 (the number of extruder steps to take in 1mm of filament)
|
||||
+G21 (metric values)
|
||||
|
@ -44,25 +44,26 @@
|
|||
+G21
|
||||
+G90 (absolute positioning)
|
||||
+G21
|
||||
+G28 (move X/Y/Z to min endstops)
|
||||
+G28 X0 Y0 (move X/Y to min endstops)
|
||||
+G28 Z0 (move Z to min endstops)
|
||||
+G21
|
||||
+G21 ( if your prints start too high, try changing the Z0.0 below )
|
||||
+G21 ( to Z1.0 - the number after the Z is the actual, physical )
|
||||
+G21 ( height of the nozzle in mm. This can take some messing around )
|
||||
+G21 ( with to get just right... )
|
||||
+G21
|
||||
+G92 X-105 Y-105 Z0.0 E0 (reset software position to front/left/z=0.0)
|
||||
+G92 X0 Y0 Z0 E0 (reset software position to front/left/z=0.0)
|
||||
+G21
|
||||
+G1 Z15.0 F400 (move the platform down 15mm)
|
||||
+G1 X0 Y0 F3500 (go to the middle of the platform)
|
||||
+G92 E0 (zero the extruded length)
|
||||
+G21
|
||||
+G1 F75 E15 (extrude 15mm of feed stock)
|
||||
+G1 F75 E13.5 (reverse feed stock by 1.5mm)
|
||||
+G1 F75 E5 (extrude 5mm of feed stock)
|
||||
+G1 F75 E3.5 (reverse feed stock by 1.5mm)
|
||||
+G92 E0 (zero the extruded length again)
|
||||
+G21
|
||||
+M1 (Clean the nozzle then press YES to continue...)
|
||||
+G21
|
||||
+G1 X100 Y100 F3500 (go to the middle of the platform)
|
||||
+G1 Z0.0 F400 (back to Z=0 and start the print!)
|
||||
+(end of start.txt)
|
||||
+
|
||||
|
@ -260,7 +261,7 @@
|
|||
|
||||
--- ori/45/skeinforge_application/skeinforge_plugins/craft_plugins/multiply.py
|
||||
+++ target/SF45/skeinforge_application/skeinforge_plugins/craft_plugins/multiply.py
|
||||
@@ -112,7 +112,7 @@
|
||||
@@ -112,11 +112,11 @@
|
||||
self.fileNameInput = settings.FileNameInput().getFromFileName(
|
||||
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Multiply', self, '')
|
||||
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute('http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Multiply')
|
||||
|
@ -268,7 +269,13 @@
|
|||
+ self.activateMultiply = settings.BooleanSetting().getFromValue('Activate Multiply', self, True)
|
||||
settings.LabelSeparator().getFromRepository(self)
|
||||
settings.LabelDisplay().getFromName('- Center -', self )
|
||||
self.centerX = settings.FloatSpin().getFromValue(-100.0, 'Center X (mm):', self, 100.0, 0.0)
|
||||
- self.centerX = settings.FloatSpin().getFromValue(-100.0, 'Center X (mm):', self, 100.0, 0.0)
|
||||
- self.centerY = settings.FloatSpin().getFromValue(-100.0, 'Center Y (mm):', self, 100.0, 0.0)
|
||||
+ self.centerX = settings.FloatSpin().getFromValue(-100.0, 'Center X (mm):', self, 100.0, 105.0)
|
||||
+ self.centerY = settings.FloatSpin().getFromValue(-100.0, 'Center Y (mm):', self, 100.0, 105.0)
|
||||
settings.LabelSeparator().getFromRepository(self)
|
||||
settings.LabelDisplay().getFromName('- Number of Cells -', self)
|
||||
self.numberOfColumns = settings.IntSpin().getFromValue(1, 'Number of Columns (integer):', self, 10, 1)
|
||||
--- ori/45/skeinforge_application/skeinforge_plugins/craft_plugins/raft.py
|
||||
+++ target/SF45/skeinforge_application/skeinforge_plugins/craft_plugins/raft.py
|
||||
@@ -338,7 +338,7 @@
|
||||
|
|
Loading…
Reference in New Issue